DOEPFER Dark Energy III Informasi Teknis Tambahan - Halaman 3

Jelajahi secara online atau unduh pdf Informasi Teknis Tambahan untuk Synthesizer DOEPFER Dark Energy III. DOEPFER Dark Energy III 6 halaman.

Halaman Cetak

Function of the jumpers / pin headers /

Name Function

JP1

Bus Connector

JP2

CV1 Bus

JP3

VCF tracking source

JP4

VCO tune range

JP5

Audio

Bus/+5V

JP6

VCF Output

JP7

Socket 7 = LFO1 Reset

JP8

Socket 8 = LFO2 Reset

JP9

Socket 2 = PWM

JP10

Socket 4 = CV VCA

JP11

Gate bus

JP12

free bus pin -> VCF

JP13

LFO1 Triangle

JP14

LFO1 Rectangle

JP15

LFO2 Triangle

JP16

LFO2 Rectangle

JP17

ADSR Out

JP18

Inputs/outputs VCO

JP19

Inputs/outputs VCO

JP20

Inverter 1

JP21

Inverter 2

DARK ENERGY III - Additional Technical Information – Page 3

soldering points

Explanation

16 pin connection to suppy/interface board

(compatible to A-100 bus)

Connects the CV line of JP1 to the VCO frequency control voltage

input (works in addition to the VCO F socket)

Selects the CV source for VCF tracking (can be turned on / off / half

by means of the Track switch):

Upper position: VCF tracking controlled by the VCO F socket

Lower position: VCF tracking controlled by the CV line of JP1

Adjusts the range of the VCO tune control:

tune range about ± 2.5 octaves

installed

tune range about ± 6 semitones

not installed

Connects the audio output of the voice board to an auxiliary pin of

JP1. Required if socket CV4 is used as audio output.

pin header with the filter outputs

lowpass (L) - left pin

high pass (H) - center pin)

band pass (B) - right pin)

Connects socket 7 to the Reset input of LFO1

the left pin is socket 7

the right pin is the Reset input

(can be used e.g. to assign another function to socket 7, in this case

the printing of the housing is no longer valid)

Connects socket 8 to the Reset input of LFO2

the left pin is socket 8

the right pin is the Reset input

(can be used e.g. to assign another function to socket 8, in this case

the printing of the housing is no longer valid)

Connects socket 2 to the PWM input of the VCO

the lower pin is socket 2

the upper pin is the PWM input

(can be used e.g. to assign another function to socket 2, in this case

the printing of the housing is no longer valid)

Connects socket 4 to the CV input of the VCA

the upper pin is socket 4

the lower pin is the CV input of the VCA

(can be used e.g. to assign another function to socket 2, in this case

the printing of the housing is no longer valid)

Connects the Gate line of JP1 to the switching contact of the ADSR

Gate socket

Connects an unused pin of JP1 to the switching contact the VCF F

socket. Not supported by the suppy/interface board.

Triangle output of LFO 1

Rectangle output of LFO 1

Triangle output of LFO 2

ADSR output

JP18A: Linear FM input VCO (left pin)

JP18B: Triangle output VCO (center pin)

JP18C: Soft Sync input VCO (right pin)

JP19A: Sawtooth output (left pin)

JP19B: Hard Sync input (center Pin)

JP19C: Rectangle output VCO (right pin)

JP20A: Inverter 1 input (left pin)

JP20B: Inverter 1 output (right pin)

JP21A: Inverter 2 input (right pin)

JP21B: Inverter 2 output (left pin)

(Dark Energy III Voice Board):

Factory default

connected to

supply/interface

board via ribbon

cable

installed

(lower position)

not installed

(put on one pin

only)

installed

open

installed

not used

open