Doheny's 2459 Series Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Instalasi untuk Filter Kolam Renang Doheny's 2459 Series. Doheny's 2459 Series 3 halaman. Automatic chlorine feeders

Halaman Cetak

6 Drill a 3/8 in. hole at location identified in Step 2 of

Planning Installation section. Install Saddle Fitting

as in Step 5 above.

7. Connect inlet and outlet tubing to the Saddle Fittings

with Compression Nuts as in Step 3 above. Do not

over tighten.

Notice

: After starting up system, re-check all

Connections for leaks. Re-tighten as required.

II DIRECTIONS FOR USE

General

Before using your chlorine feeder, your pool/spa

water should be properly balanced and conditioned

and should have a chlorine residual of approximately

1.0 to 1.5 ppm. Follow chemical manufacturer's

directions and instructions. Check chlorine residual

daily and adjust the dial valve for more or less

chlorine. The chlorine demand for pools and spas

varies based on usage, temperature and sunlight.

Initially, you'll have to experiment to determine

the proper amount of chlorine and the correct valve

setting required for your pool and filter time cycle.

Follow chemical manufacturer's instructions for

proper chlorine level.

Refilling Chlorine feeder

DANGER

• You can use 3 in. or 1 in. diameter slow-dissolving

Trichloro-S Triazinetrione Chlorine Tablets.

• Never mix chemicals as it may cause fire and/or

an explosion.

• Never mix Trichloro-S-Triazinetrione Chlorine

Tablets with Calcium Hypochlorite, or with any

other form of concentrated chlorine or other

chemicals. Fire and/or explosion may result.

• Never add any other types of chlorine, pH

adjusters, shock treatments or algaecides through

the skimmer. If these products must be used, they

should be added directly into the pool water.

• Never isolate chlorine feeder with valve or other

Devices.

WARNING

• Read and follow all Safety Instructions prior to

operating or servicing this chlorine feeder.

• To reduce the risk of injury, do not permit children

to use this product.

• Wear eye and skin protection while maintaining or

servicing this unit.

• Do not inhale fumes from the chlorine feeder or

chemical container.

• Chlorine feeder may be under pressure. Use

Caution removing cover.

10411 80th Avenue Pleasant Prairie, WI 53158 | Orders and Customer Care: 1-800-574-7665 | Fax: 1-800-323-5932 | Doheny.com

1. Shut off all pumps and pump timers.

2. Turn chlorine feeder flow control valve to 'OFF'

3. Verify chlorine feeder return line to pool is

unrestricted.

4. Wait one minute to relieve system pressure before

attempting to remove cover.

5. Remove cover.

6. Refill chlorine feeder with 3 in. or 1 in. diameter slow-

dissolving Trichloro-S-Triazinetrione Chlorine Tablets.

7. Secure cover to chlorine feeder.

8. Turn flow control valve to desired setting. Restart pump.

III MAINTENANCE

A To Change O-Ring 2458

1. Read and follow instructions in Step 1 to 5 in Refilling

Chlorine feeder section.

2. Remove the O-Ring and replace with a Doheny's

replacement O-Ring part #24572.

3. Replace cover. If chlorine feeder needs to be refilled,

read and follow instructions in Steps 6 to 8 in Refilling

Chlorine feeder section.

A To Change O-Ring 2457 & 2459

1. Read and follow instructions in Step 1 to 5 in Refilling

Chlorine feeder section.

2. Replace O-Ring with a Doheny's replacement

O-Ring part # 24573. Reassemble being sure Slip

Washers are in place on stem of Cover (Inside).

3. Replace cover. If chlorine feeder needs to be refilled,

read and follow instructions in Steps 6 to 8 in

Refilling Chlorine feeder section.

B To Remove Flow Control Valve Handle

Set pointer to FULL. Insert screwdriver in slot

opposite

pointer,

counterclockwise. This allows the handle index lock

tab to clear the body ridge.

C Winterizing

Where freezing temperatures can be expected, drain

all water from chlorine feeder, (For in-line

permanently- installed unit, remove drain plug).

Carefully remove undissolved tablets and rinse out

chlorine feeder thoroughly with water. Replace cover

and drain plug.

D Vacuuming

When vacuuming, close flow control valve to prevent

bypass of sediment and possible clogging of control valve.

E Lubrication

Never use petroleum type lubricants on Cover

O-Ring. Use Magic Lube part #1185 to lubricate.

lift

and

rotate

handle