Acquisitions XF-1000M LPG Instalasi & Petunjuk Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Instalasi & Petunjuk Pengguna untuk Perapian Dalam Ruangan Acquisitions XF-1000M LPG. Acquisitions XF-1000M LPG 16 halaman.

Halaman Cetak

2.0

APPLIANCE DATA

Gas Group

Inlet Pressure

Regulator Pressure

Max Energy Input (Gross)

Max Energy Input (Net)

Max Gas Rate

Min Energy Input (Gross)

Min Energy Input (Net)

Pilot Energy Input (Gross)

Burner Pressures -

High Hot (±1.5 mbar).

High Cold (±1.5 mbar).

Low Hot (± 0.75 mbar).

Low Cold (± 0.75 mbar).

Flow restrictor orifice

Injector

Oxypilot (SIT/Bray)

Gas control

Gas Inlet restrictor elbow

Ignition

Spark Gap (± 1.0mm)

Please see Data label affixed to appliance for current data.

This appliance is for use only with the gas type, and at the pressure stated on the appliance Data label.

3.0

INSTALLATION REQUIREMENTS

This appliance may be installed with or without a hearth. If a hearth is fitted, the size and design may

be as desired. If the appliance is to be sited near a disused natural draught flue it is recommended that

the old flue should be partially sealed off to prevent draughts, however some ventilation will be required

to prevent condensation. The appliance is designed to be wall mounted. It is possible to install the appli-

ance onto certain types of combustible materials - see section entitled 'Clearances to combustible mate-

rials'. Propane/LPG models must not be installed in cellars, basements or any room which is completely below

ground level. In the event that the fire is sited near a disused or unserviceable fireplace served by a nat-

ural draught flue, any existing under grate draught device should be sealed off to prevent loss of heat

or creation of draughts. The passageway into the flue should be partially sealed to prevent excessive

draughts, however some ventilation will be required in the old flue to prevent condensation and damp-

ness. Advice should be sought from your local building control officer.

3.1

ROOM SIZING

X-Fire 1000 models : The room size should be a minimum of 30m

adequate circulation of air and ensure the correct operation of the fire.

X-Fire Widescreen models : The room size should be a minimum of 40m

allow adequate circulation of air and ensure the correct operation of the fire.

This volume may include adjacent spaces but these spaces must not be separated by a door. To calcu-

late a room size in cubic metres (m

4.0

SITE REQUIREMENTS

This appliance is designed to be wall-hung. Do not recess any part of the appliance into the

wall.

This Appliance may be installed in any room in a home,except bedrooms and bathrooms.

Installation in living rooms is common, however other rooms such as kitchens, dining rooms and hall-

ways are permitted, providing a suitable natural gas supply is available, and rooms sizing and venti-

lation requirements are strictly adhered to (see section 4.1).

The appliance is designed to be versatile, and as such will operate correctly when exposed to normal

gentle draughts experienced within the home. It is not recommended, however that the appliance be

1000 Natural gas

G20 Natural Gas CAT I2H

20 mbar (± 2.0mbar)

N/A

2.6 kW

2.35 kW

0.23 m 3 /h

1.5 kW

1.35 kW

166 W

150 W

13.5 mbar

13.0 mbar

4.2 mbar

3.7 mbar

1.30 mm

N/A

SIT/Bray 9082

BM733

8mm

Piezo spark

4.0 mm

) divide the room volume in cubic feet (ft

1000 LPG

Widescreen Natural gas

G31 Propane CAT I3P

G20 Natural Gas CAT I2H

37 mbar (± 2.0mbar)

20 mbar (± 2.0mbar)

24.5 mbar

N/A

2.2 kW

3.5 kW

2.0 kW

3.15 kW

0.085 m 3 /h

0.34 m 3 /h

1.5 kW

2.0 kW

1.38 kW

1.8 kW

166 W

152 W

150 W

14.0 mbar

17.5 mbar

13.8 mbar

17.0 mbar

6.0 mbar

5.8 mbar

5.3 mbar

1.03 mm

1.45 mm

1.30 mm (single)

N/A

Seagas P5-19

SIT/Bray 9115

BM733

8mm

Piezo spark

4.0 mm

Widescreen LPG

G31 Propane CAT I3P

37 mbar (± 2.0mbar)

24.5 mbar

3.0 kW

2.75 kW

0.115 m 3 /h

2.0 kW

1.85 kW

166 W

152 W

14.0 mbar

13.7 mbar

6.0 mbar

5.9 mbar

1.45 mm

1.30 mm (single)

Seagas P5-22

BM733

8mm

Piezo spark

4.0 mm

(e.g. 11'6" x 11'6" x 8') to allow

(e.g. 13'4" x 13'4" x 8') to

) by 35.3.