Ashly ne800 Panduan Pengoperasian - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Penguat Ashly ne800. Ashly ne800 16 halaman. Network enabled two channel power amplifiers
Juga untuk Ashly ne800: Panduan Pengoperasian (12 halaman), Panduan Pengoperasian (12 halaman)

Halaman Cetak

4. REMOTE AMPLIFIER CONTROL

ON/OFF/Remote Standby

The NE two channel amplifiers have three possible states, OFF, ON, and STANDBY, each with a status LED on the front

panel. Control for these three states is managed by the following:

1) Power Switch - When the power switch is turned off the amplifier is completely off, UNLESS the power switch has

been disabled from within software, in which case the power switch on the amplifier has no effect at all. If the power switch

has been disabled from software, the front panel DISABLE LED will be lit. Even if the AC power is removed, the amplifier's

internal memory will maintain the <power switch disabled> status until changed again from software. Performing a factory

reset will clear and restore all internal amplifier memory to factory settings.

2) Remote Standby Contact Closure - When these two euroblock pins on the back of the amplifier (see amplifier rear

panel illustration #10) are wired to a switch and connected, the amp will go into Standby mode, whereby the amp is active but

not fully powered up. For Remote Standby to work, the power switch must be turned on OR be disabled through software.

3) Protea

Software On/Standby - On/Standby in software functions

the same as the Remote Standby contact closure on the back panel. Clicking on

STANDBY places the amp in standby mode. The On/Standby in software does

not override the hardware Remote Standby, they both remain active.

4) Protea

Software Power Switch Enable/Disable - Use this software fea-

ture to disable the front panel power switch. If the power switch has been disabled from

software, the front panel DISABLE LED will light on the amplifier. The power switch will

remain inactive until enabled again from software, even if the amp is removed from power.

Other Ashly Remote Controls for NE Two-Channel Amplifiers:

1) WR-1 DC Level Controller - The WR-1 (WR-1E) is a dual potentiometer remote DC level controller designed to fit in

a standard US (UK) electrical wall box. Each volume control can be wired to an amplifier's "Remote Level Control" connector.

1) WR-1 DC Level Controller

2) neWR-5 Programmable Button Controller - The neWR-5 is an Ethernet based programmable button controller for

networked Ashly products that have Protea DSP. The neWR-5 mounts in a standard US electrical wall box. Using Protea

buttons can be programmed for preset recall/scroll, mute, zone source selection, individual channel and matrix point level control.

3) FR-8/FR-16 Programmable Fader Controller - The FR-8 and FR-16 are Ethernet based programmable fader control-

lers for networked Ashly products that have Protea DSP. Faders and LED buttons can be programmed for individual or group

channel level control, matrix point level control, signal level display, mute, and A/B source selection. The FR remotes can be wall

mounted in an electrical box, panel mounted, or freestanding, and have a back panel contact closure for a user lockout switch.

4) Ashly Remote app for iPad

face for the Pad

can be designed using the <Ashly Remote> application, available free from iTunes

labels, and images are combined to manage key amplifier functions over a wireles network connection.

Operating Manual - NE Two Channel Power Amplifiers

2) neWR-5 Programmable

Button Controller

- For amplifiers with Protea DSP installed, a custom and secure touch-screen control inter-

Protea

Software Remote Power Control

3) FR-8 or FR-16 Programmable

Fader Controller

or the Ashly website. Controls,

software,