Ashly FR-8 Panduan Pengoperasian - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Kontrol Jarak Jauh Ashly FR-8. Ashly FR-8 12 halaman. Fr remotes network remote controls
Juga untuk Ashly FR-8: Panduan Pengoperasian (17 halaman), Spesifikasi Produk (2 halaman)

Halaman Cetak

Operating Manual - FR-8 and FR-16 Remote Level Controller

1. Network requirements

Ethernet communication is made by wiring with standard

Cat-5 cable terminated with an RJ-45 or Neutrik etherCON

connector through an Ethernet network router, switch, hub, or

patch panel to a PC running Protea NE Software v5.10 or higher.

Maximum cable distance is 100 meters (328 ft) from the nearest

router, hub, or switch. Ashly networked devices will auto detect

their Ethernet network connection, and adapt (Auto-MDIX) to either a straight through pin to pin, or

crossover Ethernet cable. Note that the push release tab on the back panel connector (as shown) is meant

only for etherCON connectors. Standard RJ-45 connectors have their own built-in release tab.

Power over Ethernet - FR remote controllers are powered using a class 2 IEEE 802.3af Power

over Ethernet (PoE) switch, hub, or in-line PoE injector. Power consumption is two watts maximum.

IP Address - There is no need to assign an IP address to FR-8/16 used with a network router. The

router or Link Local Addressing will assign IP addresses to each product automatically. When a router

is not available, most current NE products and remotes have the capability to assign their own IP address

based on Link Local Addressing. This allows the device to operate without the need to set up static IP

address. If the only option is to use an Ethernet switch instead of a router, and communications problems

remain which cannot be solved with the use of the Link Local standard, each device must have a static

IP address assigned from within Protea NE software. This is done by selecting "Manual Configuration"

in the Network Properties tab of each device, where the system/network administrator must assign each

product its own unique static IP address, each with the appropriate sub-net if applicable.

Firewalls - If Protea NE software does not detect the FR-8/16, the firewall in the host PC

should be turned off, as firewalls may block the device response to the controlling PC when network

communication is attempted. The current PC firewall status is found by clicking on the Windows

Start button, then Control Panel, then double clicking on the security shield where the firewall can

then be disabled. Once communications with the device is established, the firewall can be enabled

again, but if there continues to be communications problems then disable the firewall.

Wi-Fi and LAN – For the initial device auto-configuration process, any secondary Wi-Fi

connection should also be disabled, and the LAN (Local Area Network) connection must be enabled

on the PC. Secondary network connections may confuse the auto device discovery process. Go

to the Windows Control Panel, then Network Connections, to disable any secondary network con-

nections. Once communications with the device is established, secondary network connections can

be enabled again, unless a communications problem remains with the FR-8/16, in which case the

secondary network connections should remain disabled.

Connecting Device(s) - Connect an Ethernet cable with PoE (Power over Ethernet) to the

FR-8/16 unit. If a successful Ethernet connection has been made, a solid green LED (Link) lights up

near the device Ethernet port. If there is no green LED showing, there is either a problem with the

cable or the network source, which must be addressed before proceeding further. All RJ-45 Ethernet

ports flash green when active, so backtrack through any other cables, routers, or switches to find the

problem. The flashing yellow LED (Data) indicates that data is flowing to or from the device.

Communication Failure Indicator - If a fader has been assigned to control a specific device

function but has somehow lost contact with that device, the LED button above that fader will con-

tinually flash to indicate communication has been lost.