Ashly ne4400 Panduan Pengoperasian - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Perangkat Keras Komputer Ashly ne4400. Ashly ne4400 20 halaman. Network enabled dsp processor
Juga untuk Ashly ne4400: Spesifikasi (3 halaman), Panduan Pengoperasian (20 halaman), Manual (20 halaman)

Halaman Cetak

Operating Manual - ne8800, ne4800, ne4400

4. AC POWER AND MECHANICAL REQUIREMENTS

The AC mains requirement for the NE Processor is 90VAC to 240VAC, 50-60Hz, 70W maximum, and requires a properly

grounded AC connection. The unit mounts to a standard 19 inch equipment rack. A cooling fan draws air in from the right side

and blows air out the left side when viewed from the front.

5. GETTING STARTED

Load the software

Ashly Protea NE software is included on a CD with each unit. Check the Ashly web site at www.ashly.com to verify

that you are installing the latest software release. Autorun will launch the application<ProteaSystemSoftwareNE> to install the

Protea software. A note about firewalls: When running Protea NE software on a PC for the first time, Windows will prompt

the user to allow the software through any active firewalls. Allow this. Once the software is properly installed, Windows must

be configured to permanently allow a firewall exemption for Protea NE software.

Connect to Ethernet

The Ethernet control connection is made using an RJ-45 terminated eight conductor cable connected directly to a computer

or indirectly over a standard 10/100M Ethernet network. Maximum cable distance for Ethernet is 100 meters from the nearest

hub or switch for copper twisted pair CAT5 cable. For more detailed information about the proper implementation of an ethernet

network, review one of the many comprehensive Ethernet networking guides available on the internet.

Identify the processor in software

Once the software is loaded to the computer and an Ethernet connection has been made to the NE processor, all Ashly NE

products installed on that network will be automatically detected and shown in the active device listing on the left side of the

Protea software startup canvas. In addition to detecting which models are currently online, any factory installed options (mic

preamps, AES3, CobraNet) are also detected and the software control surface for the new NE product automatically displays

available controls for the options present. Note: In the event of multiple processors of the same model on the network, the user

can find a single physical unit by right clicking over the unit's name in the drop down menu or picture on the canvas, and then

click <Identify>, which will flash the Com LED on that unit's face panel for two seconds.

The software scans for active NE devices on power-up, but the user can manually scan at any time as well with <Scan For

Devices> at the bottom of the network NE device listing. Also, all NE devices continuously broadcast their availability to the

software. All currently connected and active NE products are highlighted in green, while NE products which may be or have

been formerly installed but are currently off-line or unavailable show up in red. Individual NE products can be dragged onto

the project canvas to simulate physical rack installation groups, but editing each product can be done from either the product

list or the canvas.

The NE system project canvas

The project canvas is used to visually represent and control a fixed physical sound system installation, and can display

any of the Ashly NE processors, amplifiers, and remotes used in that system. The user can also place an assortment of isolated

control objects such as level faders, single LEDs, meter bars, etc, and map them to specific product functions within that proj-

ect. Once a control object is placed, right click on it to bring up its properties. Lines, rectangles, text, even image files can be

added to create a custom virtual control screen along with the NE products and individual control objects. To see all available

canvas tools, right click anywhere over open canvas. Checking <Design Mode> allows placed objects to be moved around,

while unchecking <Design Mode> locks objects in place.