Cypress Semiconductor MoBL-USB CY7C68000A Lembar Spesifikasi - Halaman 2

Jelajahi secara online atau unduh pdf Lembar Spesifikasi untuk Perangkat Keras Komputer Cypress Semiconductor MoBL-USB CY7C68000A. Cypress Semiconductor MoBL-USB CY7C68000A 16 halaman. Tx2 usb 2.0 utmi transceiver

Halaman Cetak

Applications

Mobile Applications

Smart Phones

■

PDA Phones

■

Gaming Phones

■

MP3 players

■

Portable Media Players (PMP)

■

GPS Tracking Devices

■

Consumer Applications

Cameras

■

Scanners

■

DSL Modems

■

Memory Card Readers

■

Non-Consumer Applications

Networking

■

Wireless LAN

■

Home PNA

■

Functional Overview

The functionality of this chip is described in the following

sections:

USB Signaling Speed

The MoBL-USB TX2 operates at two of the rates defined in the

USB Specification 2.0, dated 4/27/2000.

Full speed, with a signaling bit rate of 12 Mbps

■

High speed, with a signaling bit rate of 480 Mbps

■

The MoBL-USB TX2 does not support the LS signaling rate of

1.5 Mbps.

Transceiver Clock Frequency

The MoBL-USB TX2 has an on-chip oscillator circuit that uses

an external 24 MHz (±100 ppm) crystal with the following charac-

teristics:

Parallel resonant

■

Fundamental mode

■

500 μW drive level

■

27 to 33 pF (5% tolerance) load capacitors

■

Document #: 38-08052 Rev. *G

An on-chip phase-locked loop (PLL) multiplies the 24 MHz oscil-

lator up to 30 or 60 MHz, as required by the transceiver parallel

data bus. The default UTMI interface clock (CLK) frequency is

determined by the DataBus16_8 pin.

Buses

The two packages enable a 8- or 16-bit bidirectional data bus for

data transfers to a controlling unit.

Suspend and Tri-state Modes

When the MoBL-USB TX2 is not in use, the processor reduces

power consumption by putting it into Suspend mode using the

Suspend pin.

While in Suspend mode, Tri-state mode may be enabled, which

tri-states all outputs and IOs, enabling the UTMI interface pins to

be shared with other devices. This is valuable in mobile handset

applications, where GPIOs are at a premium. The outputs and

IOs are tri-stated ~50ns when Tri-state mode is enabled, and are

driven ~50ns when Tri-state mode is disabled. All inputs must not

be left floating while in Tri-state mode.

When resuming after a suspend, the PLL stabilizes approxi-

mately 200 μs after the suspend pin goes high.

Reset Pin

An input pin (Reset) resets the chip. This pin has hysteresis and

is active HIGH according to the UTMI specification. The internal

PLL stabilizes approximately 200 μs after V

Line State

The Line State output pins LineState[1:0] are driven by combina-

tional logic and may be toggling between the 'J' and the 'K'

states. They are synchronized to the CLK signal for a valid

signal. On the CLK edge, the state of these lines reflect the state

of the USB data lines. Upon the clock edge the '0' bit of the

LineState pins is the state of the DPLUS line and the '1' bit of

LineState is the DMINUS line. When synchronized, the setup

and hold timing of the LineState is identical to the parallel data

bus.

Full-speed versus High-speed Select

The FS versus HS is done through the use of both XcvrSelect

and the TermSelect input signals. The TermSelect signal enables

the 1.5 Kohm pull up on to the DPLUS pin. When TermSelect is

driven LOW, a SE0 is asserted on the USB providing the HS

termination and generating the HS Idle state on the bus. The

XcvrSelect signal is the control that selects either the FS trans-

ceivers or the HS transceivers. By setting this pin to a '0' the HS

transceivers are selected and by setting this bit to a'1' the FS

transceivers are selected.

CY7C68000A

has reached 3.3V.

Page 2 of 15

[+] Feedback