Cyrus IIIi Petunjuk Pengguna - Halaman 5

Jelajahi secara online atau unduh pdf Petunjuk Pengguna untuk Penguat Cyrus IIIi. Cyrus IIIi 13 halaman. Integrated

Halaman Cetak

User Instructions

Selecting an Input

The INPUT SELECT keys

When an input key is selected, the red indicator above the key will turn

on.

Recording and Playback

You can listen to a recording by selecting key

key - TP. The indicator above the TP key will light in addition to the

selected source. To cancel, press the TP key again. If your tape deck has

a three-head facility, you can use the TP key to monitor the recording

directly from the third head, whilst recording.

To record, press the relevant Key

instructions in your tape deck manual.

Volume and Balance

(Refer to fig 4)

The LEVEL CONTROL

of the Cyrus IIIi performs the dual functions of

volume and balance.

Volume: In normal mode the LEVEL CONTROL controls the volume in

1dB steps The light ring around the knob is calibrated to show the current

loudness level. When the volume is at minimum the first indicator on the

light ring will be RED. As the volume increases a GREEN light moves

clockwise around the ring. The volume setting is always preserved when

the unit is put into standby mode.

Balance: Press the BALANCE control key

LEVEL CONTROL

to that of Left/Right Balance. The light ring works in

"reverse video" with the unlit section indicating the position of L-R

balance. You can alter L-R balance by up to +/-4dB and switch one

channel off completely when the control is turned to an extreme.

Mute

Pressing the MUTE Key

will fade the volume to minimum level without

disturbing the existing setting. When muted the RED minimum level

indicator will light as well as the existing GREEN light to show that the

output is muted. Move the volume knob or press the Mute key to fade

back up to the original volume setting.

Bi-amping / Tri-amping

The pre-amplifier output of the Cyrus IIIi may be used in conjunction with

added power amplifiers to upgrade your loudspeaker system through Bi-

amping or Tri-amping. The Cyrus Power is recommended for this

application.

Programmable Input Sensitivity

You may find an audible difference in level when switching from one input

to another due to the differing outputs of your source components. The

unique calibration memory of the Cyrus IIIi can be programmed to match

the sensitivity of all inputs with reference to the CD input. To program an

offset:

1. Select CD input and set the volume control to a comfortable

listening level.

2. Select the desired input and hold the input key down. The volume

display switches to show input offset.

3. Adjust the level to the same audible volume as the CD player. The

display will read the offset applied.

4. Press the input key again to store this setting.

Repeat Steps 2 - 4 for each input to set the appropriate sensitivity level.

Fig. 5(a) - 5(c) shows settings for Input Sensitivity levels set -2 dB, 0dB

and +2dB relative to the CD input respectively.

G B

switch selected line level input sources.

, the TAPE MONITOR

and follow the recording

to change the mode of the

(Refer to fig 5)

CYRUS AUDIO COMMANDER

To insert the batteries. Remove the battery cover on the rear of the

handset. Insert the AAA batteries observing all the polarity markings.

Replace the compartment cover.

Operating the Cyrus Audio Commander

Key to the Audio Commander drawing (Fig. 3)

Keys 1 -9 affect the operation of the Cyrus IIIi

1. Select the VI input

2. Select CD and TU inputs

If you have a Cyrus CD Player or Cyrus FM7 Tuner, pressing a key

will switch the appropriate unit on together with the Cyrus IIIi.

3. Select AUX or SP input

4. Toggle TAPE MONITOR On/Off

5. Adjust Volume

6. Select BALANCE

7. Select MUTE

8. Switch OFF all Cyrus units

9. Switch ON the Cyrus IIIi.

If CD or TU inputs have been selected with the Audio Commander,

the following keys 10-20 will control a Cyrus CD Player or the Cyrus

FM7 Tuner-

10. Select Play ............................................................Cyrus CD Players

11. Select Pause .........................................................Cyrus CD Players

12. Select FAST FWD / REV.......................................Cyrus CD Players

Auto tune - SEEK UP / DOWN.........................................Cyrus FM7

13. Select NEXT/PREVIOUS track .............................Cyrus CD Players

Select Preset UP / DOWN................................................Cyrus FM7

14. Select STOP / EJECT ...........................................Cyrus CD Players

15. Store a Program ....................................................Cyrus CD Players

Store a Preset ..................................................................Cyrus FM7

16. Numeric Keypad........................................Cyrus CD Players & FM7

17. Switch Display On / Off .............................Cyrus CD Players & FM7

18. Set Absolute Phase...................................... Cyrus dAD3 CD Player

Set Repeat ....................................................Cyrus dAD1 CD player

19. Select Elapsed Time / Time remaining .................Cyrus CD Players

20. Select MONO / STEREO .................................................Cyrus FM7

Cyrus llli

(Refer to Fig 3)