Asko 1805 FI Panduan Petunjuk Instalasi - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Mesin pencuci piring Asko 1805 FI. Asko 1805 FI 12 halaman.

Halaman Cetak

ELECTRICAL CONNECTIONS

WARNING!

Before working on wiring for any

electrical appliance, be sure the electrical power

has been turned off at the breaker/fuse box.

WARNING!

D i s c o n n e c t e l e c t r i c a l p o w e r

supply and place a tag at the disconnect switch

indicating that you are working on the circuit.

WARNING!

E l e c t r i c a l

connections must comply with the applicable

portions of the national electrical code and/or

other local electrical codes.

The electrical supply must be a 110–120 volts, 15 or 20

amp properly grounded circuit. No other appliance or

outlets should be on this circuit.

GROUNDING INSTR

OUNDING INSTRUCTIONS

OUNDING INSTR

This unit must be grounded to operate properly. It must

be connected to a grounded metal, permanent wiring

system, or an equipment-grounding conductor must

be run with the circuit conductors and connected to the

equipment-grounding terminal or lead of the appliance.

PREP

ARING

THE DISHW

PREPARING

PREP

ARING THE DISHW

ARING

THE DISHWASHER FOR INST

THE DISHW

At this point the styrofoam, plastic wrap, and the wood

pallet (base) should be removed from the dishwasher.

Now is an excellent time to inspect for any shipping

damage. Should you find any damage, you should

report it to your dealer or builder immediately .

Be sure to remove the toe kick and toe kick insulation

which are wrapped in heavy brown paper and packed

inside the dishwasher.

THE FILL STRIPS

All ASKO dishwashers (except Models 1805FI and 1895)

have color-coded fill strips to finish off the installation.

To prevent damage to the machine, be sure to remove

the shipping screws that secure the fill strips to the

access panel. These screws are to be thrown away. Do

not replace them into the access panel.

Fill

A c c e s s

Strip

Panel

NOTE: If the cabinet opening is European measurement

(23-1/2 inches [600 mm]), remove the fill strips

to fit the dishwasher into the opening.

Page 6

a n d

g r o u n d i n g

UCTIONS

ASHER FOR INST

ASHER FOR INSTALLA

WARNING!

Do not screw the fill

strips back to the

lower access panel;

otherwise, the

machine will have to

be uninstalled if

service is necessary.

NOTE:

Access

holes

than 1-1/2" in diameter with no sharp

edges.

Damage to the dishwasher could occur if it is not

properly grounded.

WARNING!

Make sure the water supply line,

drain line and branch circuit wiring do not touch

any exposed terminals of dishwasher wiring.

ALLA

ALLATION

SLIDES FOR REAR LEGS

The unit comes with two white plastic slides for the rear

legs to protect the kitchen floor from being damaged

when you slide the unit into place. The slides simply

snap onto the bottom of the rear legs.

Protective slides for rear

legs simply snap onto the

bottom of the legs.

REMO

REMOVING

REMO

VING

VING THE

VING

THE

THE A A A A A CCESS P

THE

To remove the access panel, first remove the two screws

on each side of the access panel. There are two tabs at

the top of the access panel that hold the panel in place

against the guard plate. To remove the panel, you must

slide it down below these tabs.

REMOVING

REMO

VING

VING THE

THE

THE T T T T T OE KICK

BRACKETS

BRA

CKETS

BRA

CKETS

To remove the toe kick brackets, hold the small metal

spring tab on the outer edge of the base pan toward the

outside of the machine. Continue holding the tab as

you pull straight out on the bracket. ( Note: It may be

stubborn because it's in guide slots on the base pan.)

Toe kick bracket

must

not

larger

TION

CCESS P

CCESS PANEL

ANEL

OE KICK