1010music Fxbox 2.0 Panduan Memulai Cepat - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Unit Kontrol 1010music Fxbox 2.0. 1010music Fxbox 2.0 2 halaman.
Halaman Cetak
Mute Effects
1.
While on the Main screen, push the HOME button to enter mute editing mode. The grid cells will be green.
2.
Touch a cell to mute that effect. The cell will turn red. Touch it again to remove the mute.
3.
Push the HOME button to leave mute editing mode. A red bar appears over the names of muted effects.
Start and Configure the Step Sequencer
1.
Push the HOME button to return to the Main screen if needed.
2.
On the Main screen, touch the
3.
With the
button selected, push the INFO button to see the step sequencer parameters, including
Play
.
Step Duration
Adjust a parameter by turning the control knob next to it.
4.
To run the sequencer constantly, set the
5.
Sequence an Effect
1.
Push the HOME button to return to the Main screen if needed.
2.
Select an effect to sequence by touching the grid cell.
3.
Push the INFO button twice or thrice until the
outline moves across the grid to represent the currently playing step of the sequencer. The
number of boxes the sequencer moves through is controlled by the
The time spent in each box is controlled by the
4.
Touch the grid boxes on the touch screen to enable and disable the gate for the effect on
each step. The effect is enabled for the step when the grid box is highlighted blue.
Visually Monitor the Effects
The grid on the Main screen shows when the effects are active via a bar that is displayed below the name of the effect. If the bar is
filled, the Step Sequencer or a CV Trigger input triggered the effect. If the bar is unfilled, the effect is active because the
parameter for the effect is set to
Trigger Mode
Modulate Effect Parameters
Some of the effects have parameters that can be modulated using the External CV Inputs EXT1 through EXT8.
1.
Plug an external CV signal into one of the top three CV Modulator jacks. A bar graph appears along the bottom of the
corresponding
MOD
Note:
The right most column of CV Modulator jacks map to EXT1 through EXT4. Ext5 through EXT8 are in the column to the left
•
of that. EXT5 through EXT8 also control the trigger for the corresponding effects grid cells. EXT4 also controls playback.
2.
Touch an effect cell and press INFO to see the parameters screen for this effect.
3.
Touch one of the three black boxes below a parameter to display the Modulation Parameters screen.
4.
Use the Control Knobs to select a value for the Source parameter. This parameter specifies which signal will be used to control
this parameter.
5.
For example, choose a
EXT1
as the Source of modulation to use CV voltage to adjust the cutoff value of the FILT effect.
6.
Turn the Control Knob next to the
7.
The destination effect must be active to hear the impact of the modulator changes. Follow the steps under Apply Effects
above to activate the effect.
Learn More
Download the user manual from
swapping firmware and other advanced features.
Be sure to check for any firmware updates and join the community by registering at forum.1010music.com.
This guide was written for fxbox 2.0.3.
9/12/18 2:26 PM
button to start and stop the Step Sequencer as needed.
Play
Sequencer
Step Sequencer
Step Duration
ON
button that represents the value of the CV input.
effect cell, then choose one of the modulation squares below the
FILT
parameter to adjust how much impact the CV signal will have on the effect.
Amount
1010music.com/fxbox-support
parameter to
.
ON
screen is displayed. A box
Step Count
parameter.
.
to learn about multiple effects chains, activating the XY Pad,
Step Count
parameter.
Step Sequencer Screen
parameter. Then set
Cutoff
Copyright 1010music LLC 2018
and