Ambient Technologies RCMT Petunjuk Instalasi dan Pengoperasian

Jelajahi secara online atau unduh pdf Petunjuk Instalasi dan Pengoperasian untuk Kontrol Jarak Jauh Ambient Technologies RCMT. Ambient Technologies RCMT 2 halaman. Manual on/off remote control with timer
Juga untuk Ambient Technologies RCMT: Panduan Petunjuk Pemasangan dan Pengoperasian (7 halaman)

Halaman Cetak

RCMT

Standard Thermostatic On/Off Remote Control

INSTALLATION AND OPERATING

INSTRUCTIONS

This basic on/off remote control system provides a safe, reliable,

and user-friendly remote control for milli-volt valve gas appliances.

The system can be manually turned on and off with the transmitter.

Always check with the home owner's manual of the appliance for

additional information, warnings regarding accessory installation

before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are

missing or damaged, immediately contact the dealer from whom you

purchased the kit. Do not attempt to install any part of the kit unless

all parts are in good condition. Please keep this manual for future

reference.

CONTENTS OF KIT

Description

Quantity

Transmitter

Battery Alkaline AAA (for Transmitter)

Battery Alkaline AA (for receiver)

Receiver (Assembly) consists of:

Receiver Box

Slide Button–Black (On/RS/Off)

Wall Cover Plate–Black

Wall Cover Plate–White

Slide Button–White (On/RS/Off)

Battery Door–White

Plug-In Wiring Assembly – 22" Inches

Velcro (Loop and Hook)

Installation Instructions

#6 3/4" Screws, Zinc (for Wall Cover Plate)

#8 Screws (for ﬁ replace system control covers)

NOTE: Due to the sensitive temperature monitoring components in

the transmitter, it is necessary to allow the transmitter to stabilize to

room temperature before accurate room temperatures are dis-

played. If the transmitter is activated from a severe cold condition,

allow 15 minutes for accurate temperature readings to appear on

the LCD.

WARNING: Important Safety Information

• Read this manual thoroughly prior to installing, pro-

gramming or operating any remote control.

•

This remote control system is designed for use with a millivolt

or 24V gas valve system. Do not use this remote control sys-

tem on applications with voltages above 24 Volts AC/DC and

1 amp current.

•

This remote control system requires three (3) "AAA" and

four (4) "AA" alkaline batteries to power the transmitter and

receiver.

•

Wiring must conform to appliance requirement and building

codes/ordinances as required by local and national code

authorities having jurisdiction.

•

Do not short (or jumper) across the gas valve terminals to

test the remote control installation. This could damage the

unit and void the warranty.

•

This remote control system should only be used as described

in this manual. Any other use is prohibited and will void the

warranty.

50D0103 RCMT.indd 1

FEATURES/SPECIFICATIONS

•

Battery Powered Transmitter and Receiver

•

Easy Access Front Battery Door

•

Pre-Programmed for Quick Installation

•

16 Security Codes

•

Quick Disconnect Wiring Assembly

•

Low battery indicators for Transmitter and Receiver

WARNING: Turn appliance OFF and allow to cool before

installing or servicing. DO NOT connect 110-120 VAC

wiring to the millivolt gas control valve. The remote

operator must be installed exactly as outlined in these

instructions. Read all instructions completely before attempting

installation. Follow instructions carefully during installation. Any

modiﬁ cation of components will void the warranty and may cause

a ﬁ re hazard.

WARNING: Turn appliance OFF (at the appliance or

remote receiver) if you are away from your house for a

long period of time.

INSTALLATIONS

Receiver

The remote receiver may be wall mounted

or installed in the appliance per the appli-

ance homeowner's manual. Refer to the

Homeowner's Manual for special installation

instructions. If wall mounted, the remote

receiver must be installed in a junction box

with cover plate provided. Failure to follow the installation instruc-

tions found in the appropriate Homeowner's Manual will void the

warranty and may cause a ﬁ re hazard.

Installing Batteries

The remote receiver uses four (4) "AA" batteries. To install batteries:

1. Open the battery door by pressing the two tabs located on the

door.

2. Install the batteries as indicated in the

receiver cover.

3. Close the battery door until the door tab

snaps in place.

4. To install the receiver into a wall junction

box, snap wall cover plate to the receiver and install the receiver

with the screws provided to the junction box.

5. Install slide switch back to the receiver stem.

6. The batteries should be replaced at least once every 6 months

or when the battery indicator ﬂ ashes.

Installing Wire

This system comes with a 22 inch pre-assembled wire assembly.

Insert the white terminal to the back of the receiver. The terminal

wire block can only be installed one way. Do not force the terminal

plug onto the receiver.

Follow the homeowner's manual for connecting the two (2) 1/4"

female spade terminals to the milli-volt valve.

Connect to the two (2) 1/4" female spade wiring terminals.

Receiver

Millivolt Valve

WARNING: Make sure that the wires do not contact the

appliances any place other than at the terminals. Expo-

sure to temperatures higher than 250ºF (105ºC) may

cause the receiver to malfunction or cause a ﬁ re hazard.

Transmitter

Installing Batteries

The remote transmitter uses three (3) "AAA"

Battery

Door Tab

batteries. To install batteries:

1. Press down the battery door tab and lift up

and remove the battery door.

2. Install the batteries as indicated on trans-

mitter.

3. Close the battery door by snapping in place.

4. The batteries should be replaced at least

once every 6 months or when the battery

Back of Transmitter

indicator ﬂ ashes.

WARNING: Do not use two (2) or more remote control

systems in the same area with the same dip switch

settings, as they will communicate with each other. This

may cause the appliances to malfunction.

Setting Privacy (DIP) Switch on Receiver and Transmitter

The remote receiver and transmitter privacy (DIP) switches are pre-

set at the factory. In the event of activation or interference from other

nearby transmissions, reset the code using the following procedure:

1. Slide the code switches on the transmitter or receiver to your

choice of ON or OFF position. Switches #1, #2, #3 and #4 are

preset to "ON" for both the transmitter and receiver.

2. The switches on the transmitter and receiver must match in order

for the system to work.

3. The system is now ready to operate.

Transmitter

Dip Switch (Default)

Receiver

OPERATIONS

Transmitter

General

The RCMT Remote Control provides the manual and

timed ﬁ replace on/off operation.

The transmitter will operate the remote receiver

from 1 foot to a maximum of 30 feet. The distance is

reduced when batteries are low or when the receiver

is inside a metal enclosure.

Initial Start-up

1. After initial power up or when RESET button is

pressed, the transmitter is reset. The reset button

is located inside the battery door.

2. During system reset, all features of the LCD display will be

visible. After one second, the LCD displays will be initialized. A

typical reset display is shown beside. Note

that the temperature scale is degree F.

3. Press On button to select between °C and

°F display. It will exit setting mode automat-

ically after 10 seconds if no key is pressed.

The transmitter will send an Off signal after

reset.

12/30/2014 9:05:30 AM