ACR STOVES Woodpecker Stoves WP4 Manuale tecnico - Pagina 8

Sfoglia online o scarica il pdf Manuale tecnico per Stufa a legna ACR STOVES Woodpecker Stoves WP4. ACR STOVES Woodpecker Stoves WP4 18.

Stampa la pagina

Installation of the unit

The appliance is supplied with pre-

assembled with the flue spigot in the top

exit position and the smoke exempt stop

is contained in the installation pack within

the stove.

The woodpecker range of stoves is supplied as a non-

smoke exempt appliance, if the stove is to be installed in

a smoke exempt area, the smoke exemption stop MUST

be fitted to comply with Defra legislation.

To install the smoke exempt stop, remove the direct air

intake chamber (if already fitted) and attach the smoke

exemption stop to the rear of the secondary air slider (2

dots). Reattach the direct air intake chamber if required,

and check the slider for freedom of movement. The

appliance is now smoke exempt and the secondary air

slider will not fully close, once installed this stop should

only be removed by a competent person.

Pre-installation assembly

Carefully remove the wooden packing

crate and plastic weather shield from

the stove, open the appliance and

check the contents.

Make sure that none of the internal

components have moved in transit.

If you intend to use the appliance as a

rear flue stove please follow the below

instructions.

Remove the vermiculite baffle by lifting

and easing the rear edge forward

through the combustion chamber (WP5,

WP5Q-P/LS and WP5 PLUS).

Remove the upper steel baffle (WP5,

WP5Q-P/LS).

Remove the partially cut rear blanking

plate from the outer rear panel and

discard.

Remove the 2 x 10mm bolts located on

the inner rear blanking plate and remove

(WP5, WP5Q-P/LS and WP5 PLUS).

Reattach the flue collar to the rear exit

aperture and attach the inner blanking

plate to the top flue aperture (WP5).

For WP4 & WP4LS remove flue collar

retaining bolts and rotate collar 180°

and reaffix flue collar.

The flue system can now be installed

from the rear flue collar inline with

Building Regulations document J.

Stove installation

Prior to installation please confirm that the

correct model ACR stove has been

supplied.

Packing list

Your Woodpecker stove will contain:

• 1 x Technical manual & energy label

• 1 x Multi functional tool & DEFRA kit

• 1 x ACR heat resistant glove

• 1 x Flue collar (WP5, WP5Q-P/LS and

WP5 PLUS)

• 1 x Rear direct air connection (WP5,

WP5Q-P/LS and WP5 PLUS)

If in the unusual instance that any of these

component are missing please contact

either your suppling dealer or ACR direct

to inform as failure to do this may result in

these items incurring a charge.

Installation requirements

The installation must comply with Building

Regulations document J, European

Standards and Local authority bylaws.

Commissioning and handover

Commissioning and handover after the

installation is complete test as per Building

Regulations document J and complete the

commissioning document located in this

manual.

Failure to complete the commissioning

document contained within this manual may

invalidate the warranty.

Advise the customer to "burn in" the stove

and not to fire the appliance at full output

for at 3 - 4 days.

Explain that the stove can provide a much

higher or lower output than the rated heat

outputs depending upon fuel loads used

and how they are operated.

Warn the customer that using excessive air

(having the air controls fully open for too

long) can over-fire and irreparably damage

the stove.

Damage caused by over firing is NOT

covered by any warranty.

On completion of the installation and

commissioning, check all parts of the

appliance are correctly fitted and ensure

that the operating instructions and

operating tools (including gloves and any

multi-functional tool if supplied) for the

stove are left with the customer.

You must be sure to advise the customer on

the correct use of the appliance with the

fuels likely to be used on the stove and

warn them to use only the recommended

fuels for the stove.

14 of 32

Operating Your Stove

Always ensure that the ash drawer is fully closed before operation

of the appliance

Recommended Fuels

Wood: hardwood such as ash, oak and

beech which have been cut for at least 2

years and stored under shelter. The logs

should have a maximum moisture content

of 20%. Maximum log length 400mm,

maximum width 125mm.

Smokeless solid fuel: below 20%

petroleum based coke (WP5 only).

Prohibited Fuels

Green wood: i.e wood which is less than

2 years old with a moisture content of

above 20%.

Recovered wood: i.e pallets, railway

sleepers etc. These will have been

chemically treated and will pollute the

atmosphere and possibly overheat the

appliance.

Important note

You may also experience fumes and a

haze being given off by the stove during

the first firing and possibly for the next

couple of firings as the paint cures. This is

normal but please ensure that the room is

well ventilated during this period.

In the rare event of a malfunction due to

overheating or a chimney fire, the air slides

should be shut down completely and the

fuel allowed to burn out. In the event of a

chimney fire, once the air control has been

closed completely, dial 999 for assistance.

If the appliance has overheated, the

appliance and flue will need to be

inspected for any damage before it can be

operated again.

Housecoal or Bituminous coal: these

fuels will soot up the airways of the stove

and possibly overheat the appliance.

Petroleum Based Coke: over 20%

content - this will overheat the appliance

and possibly damage the unit.

Liquid fuels

Paraffin fire lighter blocks: these can

cause damage to the glass of your

appliance

Always check with your dealer or

directly with the manufacturer as

using the incorrect fuel may

invalidate your guarantee and

damage your appliance.

Using your appliance for the

first time

• To allow the appliance to bed in, and

fixing glues and paint to fully cure, only

fire the appliance using kindling and just

get hot for at least three fires.

• Before lighting the next small fire please

allow the appliance to return back to

room temperature.

• During these first small fires you may

experience a haze and unpleasant smell

as the paint cures, do not touch the paint

and keep the room well ventilated.

Please note that during the first firing, we

recommend a small fire is lit and that you

slowly increase the temperature to enable

the various parts to expand normally.

15 of 32