Coaguchek XS System Come iniziare

Sfoglia online o scarica il pdf Come iniziare per Apparecchiature mediche Coaguchek XS System. Coaguchek XS System 2.
Anche per Coaguchek XS System: Come iniziare (3 pagine), Manuale d'uso (2 pagine), Manuale (17 pagine)

Stampa la pagina
Coaguchek XS System Come iniziare
270034 34685 CoagXS GSG 2G
2/28/07
THE PANEL BELOW IS THE FRONT COVER.
CoaguChek
System
SETTING DATE AND TIME
1. Start Setup
To set the date and time, you'll
use these buttons:
to
change a setting or
to accept a setting.
If the meter is not already in
Setup mode, press
.
The date format flashes in the
upper right corner.
PREPARING FOR A TEST
1. Gather Items
• CoaguChek XS Meter
• Container of test strips
• Test strip code chip
• ACCU-CHEK
®
Softclix lancet
device and white lancet
TESTING
Before continuing, review
these tips for getting a good
blood drop.
11:36 AM
Page 1
®
XS
Getting Started
2. Set Date
Press
. The year flashes.
to change the year then
(SET)
to change the month
then
.
to change the day then
The time format flashes in the
upper left corner.
2. Match Code
The code number on the test
strip container and the code
chip must match.
Each box of test strips comes with
a matching code chip. Every time
you open a new box of test strips,
you must replace the code chip.
Increasing the blood flow in
your finger will help you get a
good drop of blood:
• Warm your hand. Hold it
under your arm, use a hand
warmer, and/or wash with
warm water.
• Let your arm hang by your side.
• Massage your finger from
its base.
Use these techniques until your
fingertip has good color.
GETTING STARTED
Follow these steps to get started using the meter:
1. Watch the CoaguChek XS System Training DVD. It will help you
get comfortable with the CoaguChek XS Meter and the testing
procedure.
2. Read the ACCU-CHEK
®
3. With this CoaguChek XS System Getting Started guide by the
meter, follow the steps to perform your first test.
Then, as necessary, refer to the User Manual or Package Insert:
The CoaguChek XS System User Manual is a comprehensive guide
to the meter and test strips. It is designed to provide answers to
your questions about the meter's operation and use. Also, see the
test strip package insert for more information.
INSTALLING BATTERIES & SETUP
1. Open Compartment
Open the battery compartment
on the back of the meter.
Right after you insert the batteries, you'll need to set the
date and time.
The date and time settings are important. Each time you run a
test, the meter compares its date with the test strip's expiration
date. If the test strip is expired, the meter displays an error
message and prevents you from running a test.
Whenever you put batteries in the meter, it automatically goes to
Setup mode (where you set the date and time). You can also go
to Setup mode at any time by pressing the SET button (
3. Set Time
Press
. The hour flashes.
.
to change the hour then
to change the minutes
then
.
.
Turn the meter off
.
3. Insert Code Chip
Make sure the meter is off.
With the code number facing
up, insert the code chip into
the code chip slot until it
snaps into place.
1. Wash Hands
Wash your hands in warm,
soapy water.
Make sure your fingertip is
thoroughly dry.
Softclix lancet device package insert.
2. Insert Batteries
Insert 4 AAA batteries
according to the diagram
inside the battery
compartment.
4. Check Display
Press and hold the ON-OFF
button
.
.
Make sure all the letters,
numbers, and symbols on
the display appear correctly.
See The Meter's Display section
in the User Manual to see the
full display.
Release
.
Turn the meter off
.
4. Prepare Lancet Device
Pull off the cap of the lancet
device. Insert a new white
lancet. Twist off the lancet's
protective cap. Put the cap
back on the lancet device.
Line up the notches for the
cap to fit.
2. Get Ready
Take a test strip out of the
container.
Close the container tightly.
You have 10 minutes to use a
test strip once you remove it
from the container.
).