Aktino AK4010C Installazione rapida - Pagina 3

Sfoglia online o scarica il pdf Installazione rapida per Hardware di rete Aktino AK4010C. Aktino AK4010C 4.

Stampa la pagina

#3 Provisioning

AktinoView software is used to provision and monitor the

system. Use AktinoView V3 to access the most up to date

features available. Load AktinoView software onto the

maintenance computer per the instructions on the CDROM

package.

Configuring Management Ethernet Port

AktinoView uses the Ethernet port 1 for access to the Aktino

unit. Generally, the CO unit is used to set up the system; the

RT unit can be provisioned through the CO unit.

Use one of the two following procedures to configure the

unit's Management Ethernet port.

Method #1: Initialization using the front panel Craft port

1) Connect a serial cable between the maintenance

computer and the Aktino unit's front panel craft port.

2) Start a terminal program such as HyperTerminal on the

maintenance computer. Parameters are 9600 baud, eight

bits, no parity bits, 1 stop bit, and no handshake.

3) After the unit has finished booting, a prompt

"AKxxxx>" should appear, where xxxx is the part

number of the unit. At the prompt, type bolded item:

AKxxxx> enable

4) At prompt login: type the login name*

5) At prompt Password: type the password*

6) You will be prompted to enter the following

information:

Enter TID [CO]:

Enter IPAddress [192.168.10.1]:

Enter NetMask [255.255.255.0]:

Enter Gateway [0.0.0.0]:

Enter ProxyIP-Address[0.0.0.0]: (CO only)

Enter Date (yyyy-mm-dd)[2005-08-11]: (CO only)

Enter Time (hh-min-sec)[13-03-24]: (CO only)

7) Inputs can be modified with AktinoView at a later time.

Hit enter to use the default value in the brackets.

8) Exit the terminal program.

Method #2: Initialization using the Management

Ethernet port

1) Connect an Ethernet cable between the maintenance

computer and the Aktino unit's Management Ethernet 1

port located on the back of the chassis.

2) The Aktino CO and RT units have a factory default IP

address of 192.168.10.1 and 192.168.10.2 respectively.

3) Configure the maintenance computer's IP address to

192.168.10.3 and Netmask to 255.255.255.0. Note the

maintenance computer's original settings.

AK4000 Ethernet Product Family

(see Table 2)

4) Run AktinoView using 192.168.10.1 (CO) or

192.168.10.2 (RT) as the IP address for the Aktino unit.

Enter the user name and the password*.

5) If desired, the Aktino units can now be provisioned with

AktinoView.

6) If adding the Aktino unit to the local LAN, in the

AktinoView GUI, under "Tools" in the top menu bar,

select "Quick Provisioning".

7) Configure the Aktino unit's desired IP address, subnet

mask, and gateway address for the local LAN.

8) Exit AktinoView.

9) Reconfigure the maintenance computer's IP address to

original setting.

Provisioning with AktinoView V3

Connect the Aktino unit's Ethernet 1 port to the local LAN.

Once the Management Ethernet port has been set up,

AktinoView V3 should be started to provision the circuit.

See Table 2 below for common provisioning parameters

under the AktinoView V3 Provisioning tab.

Table 2 Common Provisioning Selections

Parameter

MSPAN Rate

# Pairs

Line Powering

MSPAN SNR Margin

(MSPAN menu)

Ethernet Parameters

*NOTE: Default login name and password is

superuser. For system security, the password for

superuser should be changed.

Values

Rate (Kbps)

1 to 4 (AK42x), 1 to 8 (AK41x),

1 to 14 (AK40x)

Individual pairs can be set to UP or

DOWN in the Pair menu

Off, -135v, -185v (-185v default)

Note, line powering is not available

on the AK4x1 products.

0..18db (5db default)

Each port's parameter values can be

provisioned in the Ethernet Menus

Document 180-0008-001 R08