Euro-Pro CW250H Manuale d'uso - Pagina 5

Sfoglia online o scarica il pdf Manuale d'uso per Aspirapolvere Euro-Pro CW250H. Euro-Pro CW250H 6. Water filtration vacuum cleaner 120v, 60hz, 12 amps

Stampa la pagina

OPERATING INSTRUCTIONS

3. Lift the handle to remove the

removable cover. (Fig. 11) Empty the

water tank into a toilet or an outside

drain.

4. Carefully remove the foam

inlet filter. The foam inlet

filter should be cleaned

regularly depending on

amount of usage. A severely soiled or

clogged filter should be thoroughly

washed with fresh tepid water. A mild

detergent may be used if required.

Foam Inlet

Cover

Filter

Inlet

Removable

Plate

Cover

Guide

Rails

Water Tube

Fig. 11

Canister

5. Let the foam inlet filter

air dry completely

before replacing in vacuum.

Do not use a washing

machine to rinse the filter.

Do not use a hair dryer to dry it. Air dry

only. Never operate the vacuum without

the foam inlet filter in place.

6. The water tube may become clogged

with debris. Turn until loose then pull

from removable cover and rinse under

lukewarm water and replace. (Fig. 12)

Water Tube

Fig. 12

7. To replace removable cover, slide the

inlet plate into the guide rails inside the

canister.

NOTE:

DO NOT IMERSE THE

ELECTRICAL PART OF THE VACUUM

INTO WATER OR ANY OTHER LIQUID.

Cleaning the Flexible Hose

When using the flexible hose for picking up

liquids or other soft foods such as baby

foods or ketchup, always rinse the flexible

hose with warm water after each use before

the dirt hardens on the inside of the flexible

hose.

1. Empty the water tank of all accumulated

water and dirt.

2. Reattach the flexible hose to the

canister.

3. In a pail, pour 5 cups of warm water.

4. Turn the unit "On" and insert the flexible

hose into the pail to suck up the water.

This will rinse out the inside of the

flexible hose.

5. Once you have finished, empty the

water tank again and store your unit

away.

Motor Thermostat

IMPORTANT:

This unit is equipped

with a motor protective thermostat. If

for some reason the vacuum cleaner

should overheat, the thermostat will

automatically turn the unit off. Should

this occur:

•

Push the On/Off button once.

•

Disconnect the plug from the power

source.

•

Check the source of overheating

problem. (i.e. clogged hose or filter).

•

If clogged hose or filter is found,

unclog the hose and replace the

filters.

•

Wait at least 45 minutes before

attempting to reuse the vacuum.

•

After unit has cooled down for 45

minutes, plug in the cleaner and

push the On/Off button. The vacuum

should start again.

•

If the vacuum still does not start,

contact customer service at:

1 (800) 798-8398.

OPERATING INSTRUCTIONS

Assembling the Base Casters

The casters for the base on your new

Water Filtration Vacuum are packed and

shipped unassembled.

To assemble the

caster to the base,

simply insert the

caster stem into one

of the four (4) holes in

the base and push downward

with the palm of your hand. (Fig. 1)

Repeat for the next three (3) casters.

Using Your Water Filtration

Vacuum For Dry Vacuuming

NOTE:

Always remove the power plug

from the wall outlet before assembling or

removing accessories and/or filling or

emptying the water tank.

1. Add 5 cups, (40 oz) of water to the tank.

2. Insert plug into electrical outlet.

3. To connect the flexible hose into the air

intake duct, align the tabs on thehose

with the notches on the air intake duct.

Push in firmly and turn 90° clockwise to

lock the hose in place. (Fig. 2)

4. Attach the flexible hose to one or both

extension tubes. (Fig. 2)

Air intake

duct

Flexible Hose

Fig. 2

5. To attach the extension tubes, slide the

narrow end of one tube into the wider

end of the other. (Fig. 3)

Fig. 3

WARNING:

Water level MUST NEVER

exceed the "Max" level indicated on the

water tank. Empty tank when water level

reaches "MAX" indicator. If water is seen

to be coming from the exhaust -

immediately turn the unit off and unplug

from electrical outlet. Empty water tank

and clean. Refill water tank with 5 cups

(40 oz.) of clean water then plug unit

back in and continue working.

IMPORTANT: DO NOT operate this

vacuum when water level is below the

water tube opening. (Fig. 4)

Water Tube

Fig. 4

Fig. 1

6. Press the "On/Off" Switch to the "On"

position.

7. The flexible hose is equipped with a

manual suction control to adjust the

amount of suction required. For strong

suction ensure that suction button is

closed. To decrease amount of

suction, slide the button to open until

desired strength is obtained. (Fig. 5)

Manual

Suction

Control

To Use the Dry Vac Feature:

8. Attach the wider end of one of the

extension tubes to the flexible hose

handle.

9. Attach the other extension tube to

the first one and ensure a tight

connection.

10. Attach the desired accessory to the

narrow end of the extension tube.

11. When finished using the unit,

unplug from electrical outlet and

empty the water from the unit.

Accessories for Use With the Dry

Vac Feature:

•

Air Driven Turbo Brush

•

Dusting Brush

•

Crevice Tool

•

Floor to Carpet Brush

Using The Accessories For Dry

Vacuuming

Dusting Brush

The dusting brush is used

for the furniture, venetian

blinds, books, lamp shades

and shelves.

NOTE: Do not use the dusting

brush with wet pick-up.

Crevice Tool

For hard to reach areas use crevice

tool with the extension tube or

directly onto flexible hose.

Fig. 5