14POINT7 Spartan 3D Manuale - Pagina 2
Sfoglia online o scarica il pdf Manuale per Controllore 14POINT7 Spartan 3D. 14POINT7 Spartan 3D 4. 52mm
Stampa la paginaManual - 52mm Edge AFR + Spartan 3D
⚡How To Connect Your Wiring
•
Disconnect the negative terminal
on the battery. Connect the power
wires as shown. Warning! Always install
a fuse where +12v is indicated.
•
Connect the yellow signal wire to the
Spartan 3D Lite Wideband 0v to 5v
output at Terminal 6.
* Pay close attention to the grounding requirements
in the Spartan instructions below. (Grounds Terminal 2 & 4).
•
(Optional) Install remote button wire and connect to the gauge.
•
Install 1x felt sticky strip if required (included) on inside edge of pod.
•
Reconnect negative battery wire and start using the gauge.
⚡How To Connect Spartan Wiring - Follow All Warning information!
Terminal No:
1. Spartan Power
2. Spartan GND
3. O2 Heater Power Engine running 12v (+)
4. O2 Heater GND
5. Not Required
6. Wideband
7 - 10 Program
✔IMPORTANT: "Spartan 3D, sensor and heater" must be powered only after engine has started. (The same 12v (+) should be
used). A good place to access this 12v is from the fuel pump circuit after the relay on EFI cars.
Oxygen Sensor Exhaust Location Requirements...
The Wideband Oxygen Sensor should be installed between the
10 o'clock and the 2 o'clock position, less than 60 degrees from
vertical, this will allow gravity to remove water condensation from
the sensor. The Oxygen Sensor must be installed before catalytic
converters. The sensor should be installed about 600mm (2ft) away
from the engine exhaust port - in Naturally aspirated engines.
For Turbocharged engines, the sensor can be installed
immediately after the turbocharger (In the Dump Pipe).
Note: Diesel Engines tuned with excessive soot from
extremely rich AFR's can shorten the life of oxygen sensors.
⚠
WARNINGS From '14POINT7' Spartan 3D Manufacturer
•
Do not connect or disconnect the Wideband Sensor while
Spartan 3D is powered.
•
The Sensor will get very hot during normal operation, please
be careful when handling it.
•
The Sensor must be controlled by Spartan 3D While in an
active exhaust stream. Carbon soot from an active exhaust
can easily build up on an unpowered sensor and foul it.
•
Spartan 3D should not be used on public roads.
JRP Edge Digital Gauge - AFR + Spartan 3D Manual
*WARNING!
READ ALL SPARTAN 3D INFORMATION CARFULLY
before powering unit. Incorrect power sequence can damage
sensor and void factory warranty
•
Connects To:
•
Engine running 12v (+)
•
Ground at ECU/ cabin
Ground engine block
•
Edge yellow signal wire
(Diagnostics)
10
O'clock
•
Sensor powered before your engine is running will damage
the sensor. Starting the engine can move condensation in
your exhaust system to the sensor. If the sensor is already
heated this can cause thermal shock and the ceramic
internals inside can shatter with rapid temperature changes.
•
Leaded fuels expect short Sensor life: 100-500 hrs.
•
Spartan 3D should be installed in the driver's compartment.
Yellow signal wire → Spartan "terminal 6"
(0.3 - 1A) Fuse
Terminal 1. Fused with "Grey 1A" blade fuse (included).
Terminal 3. Fused with "Caramel 5A" blade fuse (included).
Spartan grounds must be connected to 2x different
locations! Heater ground on the engine block.
Spartan to share "ground" with ECU, gauge or inside cabin.
Terminal 6. Wideband 0v to 5v analog signal output, used
to transmit wideband signal to JRP Gauge Products,
ECU's & Dataloggers.
*Signal specifications + LED information
on page 4 above notes.
(200mm link cable)
2
O'clock
⚠
Page 2 of 4