American Standard Brook Console Table 9373.100 Istruzioni di montaggio/installazione - Pagina 3

Sfoglia online o scarica il pdf Istruzioni di montaggio/installazione per Arredamento per interni American Standard Brook Console Table 9373.100. American Standard Brook Console Table 9373.100 4. Brook console table

Stampa la pagina

After top is replaced, connect the trap to the drain assembly hand tight to check

alignment. It may be necessary to cut off part of the tailpiece (area "A") or part

horizontal leg of the trap (area "B").

Connect hot and cold supply lines to the shut off valves. Tighten trap joints for

watertight assembly.

MARBLE TOP 9476.495 WITH OVALYN 0495 UNDERMOUNT SINK...

Two people recommended for this installation

NOTE: Marble top comes pre-cut for the Ovalyn under counter mount sink and 8"

faucet spread. Also it is strongly recommended that the marble top be sealed after

installation and prior to use.

Mount the drain assembly (not included) on the sink. Be certain to apply a bead of

sealing putty on the underside of the drain (Part "A") in order to ensure a watertight seal

between the sink and drain. Remove excess putty after installing the drain on the sink.

Turn the marble top upside down and place it on a clean, scratch

resistant surface. Apply a bead of silicone adhesive to the rim of

the sink. Center the sink over the cutout and (secure it to the top

using the mounting kit provided).

NOTE: Brass inserts are preinstalled on the underside of the

marble top. Use the 4 brackets supplied with the sink mounting kit

and the 4 screws supplied with the marble top.

Turn the top right-side up and install the faucet per the manufacturer's

instructions.

Apply a bead of silicone adhesive to the rim of the vanity. Place the marble top

centered left to right on the vanity and with the back edge of the top even with the

rear of the vanity. Clean up any excess silicone.

Connect the trap to the drain assembly hand tight to check alignment. It may be

necessary to cut off part of the tailpiece (area "A") or part horizontal leg of the trap

(area "B").

Connect hot and cold supply lines to the shut off valves. Tighten trap joints for

watertight assembly.

Care and Cleaning of Vanity

Clean the product by using s oft, slightly damp cloth. Buff the product by using a soft dry cloth. Avoid using silicone cleaners and waxes.

Clean up excess water and spills immediately. Use a blotting rather than a wiping action. Water left over a long period of time will cause white

spots in the finish.

NOTE: Please note that some chemicals may damage the finish. Take care to avoid the following: iodine, hair dye, after shave lotion, shaving

cream, alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula

409®, Tile-X®, and Nair®.

Care and Cleaning of the Marble Vanity Top

Marble is porous and easily stained. Wipe off anything spilled on it immediately. It should be washed or cleaned regularly with fresh warm water

and a non-abrasive clean cloth. Also, using a non-abrasive, neutral (pH balanced) cleaner will help remove dirt and grime, but it is recommended to

first try warm water only.

Marble should be sealed regularly with a good quality marble sealer. Marble sealers are available at most retail home supply stores. Follow the

instructions on the sealer container for proper application and frequency of use. The sealer acts as a stain inhibitor and prevents most stains and

soil from being absorbed into the porous surface, but it is NOT a guarantee against staining. All spills should be cleaned immediately. Avoid

contact with all oils and petroleum-based products. Also, avoid contact with all acid or caustic products such as vinegar, citrus or fruit juices, soda,

chlorine, and nail polish remover. If the marble is well sealed, the warm water and non-abrasive cloth should keep it clean.

- 3 -

73 0 5 5 1 - 1 0 0 R e v. C