D2D 3102 Manuale di installazione con riferimento rapido

Sfoglia online o scarica il pdf Manuale di installazione con riferimento rapido per Sistema di sicurezza D2D 3102. D2D 3102 2. Vehicle security system

Stampa la pagina

Quick Reference Install Guide

Vehicle Security System

Model 3102

Wiring Connections

Domelight Supervision

Output (pin #87 of onboard

relay): Connect to (-) ground

if the domelight circuit is

negative or to +12V if the

Trunk Release Output: Connect to the

domelight circuit is positive.

vehicle negative (-) trunk release relay or

other low current device. NEVER connect

directly to a motor or high current device

without a relay.

12V Constant Power Input: Remove the

inline fuse before connecting to a wire

that has (+) 12V at all times. Reinstall the

inline fuse when wiring connections are

complete.

Siren Output: Connect to the (+) wire on

the siren.

+12V Ignition Input: Connect to a wire

that has (+) 12V while the key is in the

run and crank positions.

Chassis Ground Input: Connect to a

scraped (bare) metal surface in the driver

kick panel. NEVER connect to dash

brackets or to a factory ground.

Door Trigger Input:

Green: Connect to a wire that rests at (+)

12V when all doors are closed and (-)

ground when any door is opened.

Violet: Connect to a wire that rests at

ground when all doors are closed and

(+) 12V when any door is opened.

Instant Trigger Input: Connect to a wire

in the vehicle that goes to ground when

opened (typically the trunk) or to an op-

tional Directed single zone sensor.

Domelight Supervision Output (pin #30

of onboard relay): Connect to a wire that

turns on the domelight to illuminate the

vehicle interior when disarming and turn-

ing off the ignition

Aux 1 Output: Connect to an auxiliary

convenience or expansion option. NEV-

ER connect directly to a motor or high cur-

rent device without a relay.

(+ or -) Light Flash Output: Connect to

the vehicle parking light wire. Select the

correct polarity with the output or vehicle

damage may occur.

(87A) Normally Closed: To car side of

starter wire if programmed as a Nor-

Ground When Armed Output: Connect

mally Closed circuit (factory default).

to a starter interrupt relay or an accessory

that requires a ground to activate when

(87) Normally Open: To car side of

the system is armed.

starter wire if programmed as a Nor-

mally Open circuit.

Important: NEVER connect 200mA low current outputs

(30) Common: To key side of starter

directly to a motor or high current device WITHOUT

wire.

a relay,

Bitwriters with a date code of 6a or older require an IC

upgrade (p/n 998M). Some bitwriters with a date code

of 6B do not require the IC upgrade, refer to tech tip #

1112 for more information.

Pin #87A of Onboard

Pin #30 of Onboard

Door Lock Relay:

This wire is typically

Connect to the door

used whenever the door

lock wire in the vehicle.

lock switch needs isola-

tion.

Note: For more door lock wiring information, see tech tip #1041 at: www.directechs.com (authorized users only).

Valet Switch

Sensor 2

Note: The sensor ground outputs from the system

are only active when the system is armed.

Sensor 3

Violet

(87) of onboard Unlock Relay

Blue/Black

(30) of onboard Unlock Relay

Brown/Black (87A) of onboard Unlock Relay

Violet/Black

(87) of onboard Lock Relay

Green/Black (30) of onboard Lock Relay

White/Black (87A) of onboard Lock Relay

Black/White (87) of onboard Domelight Sprvsn Relay

Red/White (-) 200mA Trunk Release Output

Red

(+) 12V Constant Power Input

Brown

(+) Siren Output

Yellow

(+) Switched Ignition Input

Black

(-) Chassis Ground Input

Violet

(+) Door Trigger Input

Blue

(-) Instant Trigger Input

Green

(-) Door Trigger Input

Black/White (30) of onboard Domelight Sprvsn Relay

White/Blue

(-) 200mA Aux 1 Output

White

(+ or -) Selectable Light Flash Output

Orange

(-) 500mA GWA Output

Green/Black

Green

Green/White

The Bitwriter® (p/n 998U)

requires chip version 2.4 or

newer to program this unit.

Pin #87 of Onboard

Pin #87A of Onboard

Pin #30 of Onboard

Door Lock Relay:

Door Unlock Relay:

Connect to (-) ground if

This wire is typically

Connect to the door un-

the locks are negative

used whenever the door

lock wire in the vehicle.

or to +12V if the locks

lock switch needs isola-

are positive.

tion.

998T Bitwriter

/SmartStart

Antenna

Detail

Parking Light

Flash Jumper

(-) 200mA OEM Alarm

Disarm Output

Lt. Green/Black

Lt. Brown

(-) 200mA Horn Honk Output

Violet/Black (-) 200mA Aux 2 Output

White/Black (-) 200mA Aux 3 Output

Gray/Black (-) 200mA Aux 4 Output

Orange/Black (-) 200mA Retained Acc Output

Gray

(-) Hood Trigger Input

Lt. Blue (-) 200mA 2nd Unlock Output

LED

Remote control configuration

4- button remote control configuration

Feature

Description

Arm: Lock the doors and arm the vehicle

Disarm: Unlock the doors and disarm the vehicle

Pin #87 of Onboard

Trunk Release/Silent Mode: Activate Silent Mode

AUX

Door Unlock Relay:

and Auxiliary functions

Connect to (-) ground if

Panic

A U X

the locks are negative

A U

or to +12V if the locks

are positive.

Aux 1: Press together to control an Auxiliary output

and

Programming System Features

The System Features Learn Routine dictates how the unit operates. It is possible to

A U

access and change most of the feature settings using the Valet switch.

A U X

Open a door.

Turn the ignition on, then off.

Select a Menu. Press and hold the Valet switch. The number of siren chirps

indicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu 2, and

3 chirps for menu 3.

When the desired menu chirps are heard, release the Valet switch.

Select a Feature. Press and release the Valet switch the number of times cor-

responding to the feature you wish to change. Then press and hold one more

time to select the features.

Program the Feature. While holding the Valet switch, you can program the

feature using the remote control.

To change the desired options press;

three or higher chirps setting.

Once a feature is programmed:

OEM Alarm Disarm: Connect to the

•

Other features can be programmed within the same menu

factory alarm disarm wire in the ve-

•

Another menu can be selected

hicle (if applicable). NEVER connect

•

The learn routine can be exited if programming is complete

directly to a motor or high current de-

vice without a relay.

To access another feature in the same menu:

Press and release the Valet switch the number of times necessary to advance

Horn Output: Connect to the vehicles

from the feature you just programmed to the next one you want to program.

(-) horn honk relay wire.

Then press the Valet switch once more and hold it.

Aux 2 Output: Connect to an auxilia-

ry convenience or expansion option.

To select another menu:

NEVER connect directly to a motor or

Press and hold the Valet switch.

high current device without a relay.

After 3 seconds, the unit advances to the next menu and the siren chirps, indi-

Aux 3 Output: Connect to an auxilia-

cating which menu has been accessed.

ry convenience or expansion option.

NEVER connect directly to a motor or

The learn routine exits if any of the following occurs:

•

The open door is closed

high current device without a relay.

•

The ignition is turned On

Aux 4 Output: Connect to an auxilia-

•

There is no activity for 15 seconds or more

ry convenience or expansion option.

•

The Valet switch is pressed too many times

NEVER connect directly to a motor or

high current device without a relay.

Programming continued on page 2.

Retained Acc Output: Connect to a

relay that controls the accessory cir-

cuit in the vehicle.

Hood Trigger Input: Connect to a

wire that goes to ground when the

hood is opened.

2nd Unlock Output: Connect to a

wire (or relay assembly) that unlocks

all doors when installing two stage

door unlocking.

= one chirp setting, while

= two,

AUX