eKey ekey home CP WM 3 Manuale di avvio rapido

Sfoglia online o scarica il pdf Manuale di avvio rapido per Controllori di accesso IP eKey ekey home CP WM 3. eKey ekey home CP WM 3 2. Access system with fingerprint

Stampa la pagina

QUICK START GUIDE

ekey home CP WM(IN) 1(2,3)

Access system with fingerprint

ID4/129/0/53: Version 2

dated 22.6.2012

Note on the document

This quick-start guide as well as the additional information and instructions on the

supplied DVD are not subject to updating. You can find the most up-to-date version of

these documents on www.ekey.net. Subject to optical and technical modifications,

any liability for misprints excluded.

1 Start-up

Before you start programming the system with the help of this

quick-start guide, the system must be mounted and wired

according to the mounting instructions and wiring plan supplied

with the device. Please follow the steps below:

1.) Make everything you need ready to mount the devices as

described in the mounting instructions supplied with the devices.

2.) Wiring

Do not connect the system to the mains yet! The electrical

connection of the system can only be carried out by a

specialist!

Connect the wires as described in the ekey home wiring plan supplied

with the devices.

3.) Check the wiring.

4.)

Conclude mounting the devices. Close all the device housings

which you had to open in order to be able to proceed with the wiring.

5.)

Read carefully the following chapter

„ 2 Operating the finger scanner". The correct

operation (i.e. swiping the finger over the sensor) of

the fingerprint scanner is decisive for the proper

functioning of the whole system.

6.) Connect the power adaptor to the mains.

The electrical connection of the system can only be carried out

by a specialist!

A couple of seconds later, 2 red dots show up on the display of the

ekey home CP WM (IN)1(2,3).

The ekey home finger scanner indicators are as follows:

ekey home FS WM

ekey home FS IN

ekey home FS OM

flashing

orange

Now start at point A: INITIALIZE DEVICES of „Programming

7.)

the system".

2 Operating the finger scanner

2.1.Function of the finger scanner

The function of the finger scanner is to capture and analyze the image of your finger, and then

compare it with a reference template. Which part of your finger should be captured?

Finger nail

It is necessary to capture an image of the

3rd phalanx. On the contrary, your finger

3rd phalanx

Finger

image

scanner will not function properly.

(phalanx distalis)

(papillary

lines)

of the

In order to ensure this, take care to

3rd phalanx

operate the finger scanner correctly. It is

fundamental to place your finger correctly

in the finger recess and move it down

2nd phalanx

(phalanx media)

across the sensor at the right speed.

A finger scanner works like a camera. It makes a picture of the bottom side, the papillary lines, of

your finger´s third phalanx. However, this picture must be of good quality, so that physical access

can be granted whenever necessary.

Imagine you wish to make a picture of someone, and this person

keeps fidgetting

runs by and you try to make a picture of him at that exact moment

hides half of his face behind a tree

etc.

What do you think these pictures will look like? On some of the pictures you will not even be able

to recognize the person.

The finger scanner works in the same way. The finger scanner can only read all the information

contained in your finger, and consequently open your doors securely and reliably, if you move

your finger down across the sensor evenly and in the right position.

Let us now look at where you should place your fingers and at which speed you should move them

across the sensor, so that the „pictures" of your fingers are perfect.

2.2 The finger recess – the control element

The finger recess allows to place the finger correctly so that a finger picture of good quality

can be captured. It actually is the control element and consists of

right and left recess edges.

3. Programming the system with the ekey home CP WM 1(3)

3.1.Function of the control panel

The function of the ekey home CP WM (IN)1(2,3) in the ekey

home system is to program and parametrize the system. Using

the

7-segment display and the

4 buttons,

you can

Delete users

Enter the security code

Change the security code

Change the relay switching times

Reset to factory settings

The menu navigation is intuitive and very easy. You will find

step-by-step detailed

explanations

of each specific menu

function on page 2.

2.3. Operating correctly the finger scanner

Ideally, when positioning your

finger on the finger recess, stretch

the remaining fingers, holding them

close to the „swiping" finger. This

helps keep the „swiping" finger

even.

2.4. What you should not do

Left and

right recess edge

Place your third phalanx

higher than the pin point

PIN POINT

V >>

SENSOR

pin point - sensor –

3.2.Controls and their symbols

Symbol for the 7-segment display on the ekey home CP

Represents that which is displayed on the control panel during

the programming procedure and when it is operational.

The OK button

values and move to the next menu level.

The Right arrow button

set values and navigate in the menu.

The Left arrow button

set values and navigate in the menu.

The ESC button

menu level or to cancel entries.

Lay your finger straight and flat

on the finger recess.

BE SURE to place

Place the middle of

your finger exactly

your third phalanx

in the middle of

directly on the

the area between

finger recess

both finger recess

point.

edges.

Now without changing the inclination of your finger, move it down

across the sensor (the entire hand). Take care to swipe your finger

at the right speed. BEWARE: The entire movement (swipe) should

take about

Use this as a benchmark. You should not need much more or much

less than that.

Do not modifiy the position of the finger phalanges during the

swipe (e.g. by bending the third phalanx).

There is no need to exert any

finger across the sensor as if you would wipe bread crumbs off a

table.

Not place your finger in the middle

Rotate your finger in the

of the finger recess, or not place it

finger recess.

parallel to the finger recess edges.

If you move your finger across the finger scanner in one of the

Move

your

ways mentioned here, then the scanner will not be able to

finger too fast

extract the information it needs about your finger image. It

or too slowly

will therefore not function properly:

across

the

Poor recognition performance: You will have to swipe your

sensor.

finger several times across the sensor before being able to

induce the door to open.

Reference templates cannot be saved: You are not abel to

save a finger in the system, because the fingerscanner gets less

information.

and with the ekey home CP IN 1(2)

3.3. Programming the system

Now start programming the system. The menu

sequences

for

explained below of this document. Let us not

forget to mention the security code. You need it in

order to be able to make changes in the system.

The factory default setting for this code is

allows you to register

99. Change this code to another one of your

choice as soon as you have started up the

system.

allows you

allows you to

allows you to exit a

Take care to position

your finger as flat as

possible over the

finger recess.

1-1,5sec

stronger

pressure. Move your

Place your finger at a too

steep angle with the

finger recess.

each

single

function

are