American Standard Studio Right Height 2794 Istruzioni per l'installazione Cura e manutenzione
Sfoglia online o scarica il pdf Istruzioni per l'installazione Cura e manutenzione per Servizi igienici American Standard Studio Right Height 2794. American Standard Studio Right Height 2794 4. Dual flush concealed trapway
Stampa la pagina
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
®
Studio
Dual Flush Concealed Trapway
®
Right Height
, Elongated Model 2794
®
Right Height
, Round Front Model 2795
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations
may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN
DIMENSIONS:
NOTE: Distance from wall to
closet flange centerline must
be as listed below:
IMPORTANT: Water supply
on the wall is required at
2-1/4" or 8" from centerline
of the toilet (see rough-in).
First suggested position is
hidden behind the toilet. The
geometry of the toilet gives
space for this installation.
The second suggested
position is next to the toilet.
Between these two
positions, the space for the
supply between wall and
toilet is limited to 4-1/2". In
this case, check your supply
and hose dimensions.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 2
Adjustable Wrench
Flexible Supply Tube
RIGHT HEIGHT ELONGATED 2-PIECE TOILET
FINISHED
WALL
30-1/4"
(768mm)
8-3/4"
(221mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
18-1/2"
(470mm)
7-1/2"
13-11/16"
(191mm)
(347mm)
12"
(305mm)
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
RIGHT HEIGHT ROUND FRONT 2-PIECE TOILET
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
FINISHED
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
WALL
28-1/4"
(717mm)
8-3/4"
(221mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
16-1/2"
(419mm)
7-1/2"
12-7/8"
(191mm)
(328mm)
FINISHED
12"
(305mm)
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
Sealant
Closet Bolts
15-3/4"
(399mm)
14"
(356mm)
SUPPLY
AS
REQUIRED
(position 1 or
position 2)
16-1/2"
2-1/4"
(419mm)
8"
(57mm)
(204mm)
5-1/2"
(140mm)
6"
FINISHED
(152mm)
FLOOR
12-3/16"
(309mm)
15-3/4"
(399mm)
14"
(356mm)
SUPPLY
AS
REQUIRED
(position 1
or
position 2)
16-1/2"
2-1/4"
(419mm)
8"
(57mm)
5-1/2"
(204mm)
(140mm)
6"
(152mm)
FLOOR
12-3/16"
(309mm)
Certified by
IAPMO R&T
Tape Measure
Carpenters Level
30-7/8"
(784mm)
BACK VIEW
(for reference)
30-7/8"
(784mm)
BACK VIEW
(for reference)
73 016 9 2 - 10 0 Rev. C