American Standard Colony Whirlpool/Bathing Pool 1748 Series Istruzioni per l'installazione
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Vasca idromassaggio American Standard Colony Whirlpool/Bathing Pool 1748 Series. American Standard Colony Whirlpool/Bathing Pool 1748 Series 4. Colony 5-1/2' whirlpool/bathing pool
Stampa la pagina
COLONY™ 5-1/2'
INTEGRAL APRON WITH
REMOVABLE ACCESS PANEL
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
7-1/4 (184mm)
C/L OF DRAIN
FINISHED
3/4 (19mm)
WALL
15-1/2"
(394mm)
32
(813mm)
C/L OF
SUPPLIES
2-3/8 – 1/2
(60 mm – 13 mm)
1-1/2
(38mm)
C/L OF DRAIN
OUTLET
OPTIONAL TO
FINISHED FLOOR
1" WATER
USUALLY BETWEEN
RETENTION
65 & 78
FLANGE
(1651 & 1981mm)
(3 SIDES)
C/L OF
OVERFLOW
3-1/4
(83mm)
TOP OF
DECK
19-1/2
(459mm)
ROUGH
FLOOR
BATH
SUPPORT
MATERIAL
Left-hand version shown
GENERAL SPECIFICATIONS FOR 1748 WHIRLPOOL
INSTALLED SIZE
66 x 32 x 19-1/2 In.(1676 x 813 x 495mm)
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
General Installation Information
Bath may only be installed in a recess type installation.
Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made
through access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as
indicated.
this bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position
bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary. To secure the tub to wood studs use
drywall screws w/washers or roofing nails immediately above the flange of the tub. To secure the tub to steel studs use 4" drywall screws and
flatwashers.
See page 2 for complete installation information.
Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against
the bottom of the tub apron, also holding the tub in place.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
753449-100 REV. A
1748 SERIES
WHIRLPOOL/BATHING POOL
INSTALLATION INSTRUCTIONS
66 (1676mm)
WATER RETENTION
FLANGE (3 SIDES)
ON/OFF SWITCH
C/L OF
SHOWER ARM
FINISHED
WALL
C/L OF
VALVES
C/L OF
12
SPOUT
(305mm)
LEVELING
OPT.
4
STRINGER
TILING
(102mm)
NOT FOR
FLANGE
SUPPORT
19-1/4
(489mm)
REF.
DIM
1-1/2 N.P.T.M.
THREADS
2-3/4
(70mm)
1-1/2 O.D.TAILPIECE
4-5/8
(117mm)
120 Lbs. (54 Kg.)
537 Lbs. (244 Kg.)
50 Gal. (189 L.)
46 Gal. (174 L.)
18 x 48 In. (457 x 1219mm)
26 x 59 In.(660 x 1499mm)
12-1/2 In. (318 mm)
37 Lbs./Sq. Ft. (179 Kgs/Sq. m.)
20.8
35.3
1.1 HP, 9.9 AMPS, 120V.
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to
you after careful inspection. the whirlpool version is completely
assembled with pump, motor, and system piping. All you need to finish
the installation are your selected fittings and electrical connections for
a whirlpool. To insure maximum performance and pleasure from this
product, please follow the instructions and cautions.
List of Optional Components (not included):
• Metal Air Control Kit 9850.200*
PUMP
• Jet Trim Ring Kit 9860.200*
List of Required Components (not included):
• Drain 1583.470*
* see your American Standard Dealer
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
UNDERSIDE
OF DECK
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
General Installation Information
Carefully uncrate and inspect your new bath for any shipping damage.
If such damage is found, report it to your vendor immediately. After
inspection and during installation, protect the bath from construction
damage. Before installation, and before enclosing with wallboard,
tile, etc., water test the unit and check for leaks. Do not make
modifications to the whirlpool system or remove pump from factory
mounting. This could adversely affect the safety and performance of
the whirlpool and void the warranty. Do not handle or move the
whirlpool by the pump, motor, or piping system. Fittings (bath filler,
shower arm, etc.) are not provided with the bath and must be ordered
separately. Framing and enclosing materials are provided by others.
IMPORTANT: Water test unit before installation and
enclosure!
• Bath Filler*
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
© American Standard Inc. 2005
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.