Ekinex EK-HC1-TP Manuale - Pagina 3

Sfoglia online o scarica il pdf Manuale per Controllore Ekinex EK-HC1-TP. Ekinex EK-HC1-TP 5. Controllers for fan coil

Connection of the KNX bus line
The connection of the KNX bus line is made with the
terminal block (black/red) included in delivery and
inserted into the slot of the housing.
Characteristics of the KNX terminal block
spring clamping of conductors
4 seats for conductors for each polarity
terminal suitable for KNX bus cable with single-wire
conductors and diameter between 0.6 and 0.8 mm •
recommended wire stripping approx. 5 mm
color codification:
red = + (positive) bus conductor
black = - (negative) bus conductor
Warning! In order to supply the KNX bus lines use only a
KNX bus power supply (e.g. ekinex EK-AB1- TP or EK-
AG1-TP).
The
use
compromise the communication and damage the devices
connected to the bus.
Connection of the 230 Vac line (all version)
The connection of the line is made with screw terminals
located on the upper front of the device.(Figure A).
Characteristics of the terminals
screw clamping of conductors
maximum cross section of conductor 2.5 mm²
(single wire)
recommended wire stripping approx. 6 mm
torque max 0.8 Nm
Warning! The electrical connection of the device can be
carried out only by qualified personnel. The incorrect
installation may result in electric shock or fire. Before
making the electrical connections, make sure the power
supply has been turned off..
Bus
KNX
230 Vac
L
50/60 Hz
N
a
Connection of KNX bus and 230 Vac power supply
of
other
power
supplies
can
+
-
Inputs/ Outputs Terminal
C
V1
11
12
13
IN1
3
4
Terminals
Name
3-4
IN1
5-6
IN2
7-8
IN3
9-10
0-10V
11
C
12
V1
V2
13
14
V3
15-16
DO1
17-18
DO2
The outputs that are not used for the command of the
terminal temperature control can be configured in ETS
for the control of actuators of lighting or drive .
Example
T
EK-HA1-TP:
3-speed fan, 2-pipe system, application with use of the internal
regulator and room sensor or on the recovery. attention to the
electrical connections. The outputs V1, V2, V3 and C1 must be
powered externally ( terminals 11 and 15) with the power phase:
because the system functions you must connect the other end of the
motor fan and the other end of the actuator to the conductor neutral.
Page 3
V2
V3
DO1
DO2
14
15
16
17
IN2
IN3
0-10V
5
6
7
8
9
+
Signal Type
Input 1 configurable as passive probe
temperature ( sensor NTC 10k @
25 °C ) or as a binary input (potential
free)
2 freely configurable input
3 freely configurable input ( only EK -
HC1 - TP )
Output 0 ... 10V ( for high impedance
inputs ) to control the fan with brushless
motor ( for EK- HB1 - TP and EK -HC1 -
TP )
common Input to control 3-speed motor
( for EK - HA1 - TP and EK - HC1 - TP )
Relay output fed to control the fan
speed 1
( for EK - HA1 - TP and EK - HC1 - TP )
Relay output fed to control the fan
speed 2
( for EK - HA1 - TP and EK - HC1 - TP )
Relay output fed to control the fan
speed 3
( for EK - HA1 - TP and EK - HC1 - TP )
Potential free relay output to control ac-
tuator valve heat exchange
Potential free relay output to control ac-
tuator valve heat
( only EK - HC1 - TP )
1 2
3
C
V1
V2
V3
DO1
11
12
13
14
15
16
17
18
IN1
IN2
3
4
5
6
7
8
9
10
EK-HA1-TP
Fan-coil actuator/controller
Area
230Vac-50/60Hz
Line
L
N
Dev.
bus KNX
1
2
18
10
-
N
230Vac
L