Ekinex EK-CD2-TP Manuale di avvio rapido - Pagina 3

Sfoglia online o scarica il pdf Manuale di avvio rapido per Apparecchiature di registrazione Ekinex EK-CD2-TP. Ekinex EK-CD2-TP 4.

Stampa la pagina

Connection of outputs (low-consumption LEDs)

Block

Mark

+ 5V

OUT1

OUT2

OUT3

OUT4

*) not present in the EK-CC2-TP version

Warning! The electrical connection of the device

can be carried out only by qualified personnel. The

incorrect installation may result in electric shock or

fire. Before making the electrical connections, make

sure the power supply has been turned off.

Mounting

The device has degree of protection IP20, and is therefo-

re suitable for use in dry interior rooms. The support EK-

SMG-35 allows the mounting on 35 mm rail in boards or ca-

binets for electrical distribution.

a) Insert the mounting support into the appropriate shaped profile of the

interface

b) Place the support clamping tooth on the top edge of the mounting

rail and rotate device and support towards the guide until it completely

engages

c) Once fastened, connect the bus line, the inputs and the outputs

Connection

LED power supply

Output LED 1

Output LED 2

Output LED 3 *

Output LED 4 *

Configuration and commissioning

Configuration and commissioning of the device re-

quire the use of the ETS

program V4 2.0 or later releases. These activities must

be carried out according to the design of the building au-

tomation system done by a qualified planner.

Note. The configuration and commissioning of KNX

devices require specialized skills. To acquire these

skills, you should attend the workshops at KNX cer-

tified training centers.

Configuration

For the configuration of the device parameters the corre-

sponding application program or the whole ekinex

duct database must be loaded in the ETS program. For

detailed information on configuration options, refer to the

application manual of the device available on the website

www.ekinex.com.

Application

Product

software

code

(## = release)

EK-CC2-TP

APEKCC2TP##.knxprod

EK-CD2-TP

APEKCD2TP##.knxprod

EK-CG2-TP

APEKCG2TP##.knxprod

Commissioning

For commissioning the device the following activities are

required:

• make the electrical connections as described above;

• turn on the bus power supply;

• switch the device operation to the programming mode

by pressing the programming pushbutton located on

the front side of the housing. In this mode of operation,

the programming LED is turned on;

• download into the device the physical address and the

configuration with the ETS

At the end of the download the operation of the device

automatically returns to normal mode; in this mode the

programming LED is turned off. Now the bus device is

programmed and ready for use.

Reset of the device

To reset the device remove the bus connection by ex-

tracting the bus terminal from its seat. Keeping pressed

the programming pushbutton, reinsert the bus terminal in

his seat; the programming LED blinks fast. Release the

programming button and remove the bus terminal again;

the reset was carried out. Now you need to address and

configure again the device via ETS.

Warning! The reset restores the device back to the

state of delivery from the factory. The address and

the value of the parameters set during configuration

will be lost.

Marks

• KNX

• CE: the device complies with the Low Voltage Directi-

ve (2014/35/EU) and the Electromagnetic Compatibili-

ty Directive (2014/30/EU). Tests carried out according

to EN 50491-5-1:2010 and EN 50491-5-2:2010

Maintenance

The device is maintenance-free. To clean use a dry cloth.

It must be avoided the use of solvents or other aggressive

substances.

(Engineering Tool Software)

Comm.

Group

objects

adresses

(max nr.)

255

365

program.

pro-