6
Activate and hang your clocks
Don't activate the battery or apply power to the clocks until the system controller is installed and
transmitting and the clock is in the intended location.
Activation Note:
Clocks should be installed within 24 hours
of installing the system controller. After 24 hours, the system
controller will enter Quiet Mode. Pressing 3-5-7 on the keypad
will disable Quiet Mode for 6 hours. Reference Appendix J in the
SiteSync IQ Installation and Operation Manual for more details
on Quiet Mode.
Battery Analog Clocks
1. Take the clock to the area where it will be
used.
2. To activate the clock, connect barrel jack plug
of battery pack to wireless receiver. The
LED on the back of the clock will flash red
within 30 seconds of power-up to indicate
receiver is looking for the wireless signal.
When the signal is received, the LED will flash
green. Be patient. The clock hands will rapid
advance to the correct time. This may take up
to 7 minutes.
3. Hang the clock after hands are rapid
advancing.
Note: If the LED does not flash within 30 seconds,
remove the barrel jack plug of the battery pack from
the wireless receiver for 5 seconds and reconnect it.
This resets the receiver. The LED will begin flashing
within 30 seconds.
Battery
Barrel
Jack
Input
LED
INST-SSIQ-X-P Rev 15
Electric (AC) Analog Clocks
1. Take the clock to the area where it will be used.
2. To activate the clock, connect to AC power.
The LED on the back of the clock (see below)
will flash red within 30 seconds of power-up to
indicate receiver is looking for the wireless
signal.
When the signal is received, the LED will flash
green. Be patient. The clock hands will rapid
advance to the correct time. This may take
up to 7 minutes.
3. Hang the clock once signal reception is
verified and clock is operating correctly.
Note: If the LED does not flash within 30 seconds,
disconnect the barrel plug on the clock receiver, wait
10 seconds and reconnect. The LED will begin flashing
within 30 seconds.
Electric
Reset
LED
Button
American Series Digital Clocks
1. Take the clock to the area where it will be used.
2. To activate the clock, connect to 120vac power.
3. Display will flash "U40" or 1:00 o'clock until it
receives a signal.
4. Verify synchronization takes place within 2-5
minutes
Your SiteSync IQ system is now set up for proper operation.
For information on other features, see the Installation and
Operation Manual that was included with your system. If you
have any questions, please contact Technical Support at
American Time: 800-328-8996.
SiteSync IQ
®
GPS Plus with Campus TX Antenna & External Transmitter
Please read this first!
After determining the proper wattage for your facility, we guarantee the coverage of your SiteSync IQ
when you follow a few simple steps. If this is your first installation or you have questions at any time
during this process, please call American Time toll free at
We're here to help!
This Quick Start Guide will help you avoid three common installation mistakes:
1. Improper location of transmitting (TX) antenna.
is recommended.
Don't drill holes for permanent installation and mounting until the system is working correctly.
2. Improper system controller start-up.
lower right-hand corner of the system controller screen.
Don't locate the campus TX antenna within 4' of the system controller.
3. Improper clock start-up.
Activate clocks in their intended location.
Don't activate the clocks in one room and move them to another location as signal reception
will not be verified. Make sure the system controller is transmitting and is not in Quiet Mode.
Important Note:
Clocks should be installed within 24 hours of installing the system controller. After
24 hours, the system controller will enter Quiet Mode. Pressing 3-5-7 on the keypad will disable Quiet
Mode for 6 hours. Reference Appendix J in the SiteSync IQ Installation and Operation Manual for
more details on Quiet Mode.
800-328-8996
phone:
fax:
140 3rd St. So.; PO Box 707, Dassel, MN 55325-0707
mail:
Wireless Clock System
800-328-8996
.
A temporary install of the system controller
A successful transmission is indicated by a TX in the
800-789-1882
american-time.com
online:
Stampa la pagina