AMERICAN TRUCKS T527991 Manuale di istruzioni per l'installazione - Pagina 2
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Automobile Accessories AMERICAN TRUCKS T527991. AMERICAN TRUCKS T527991 6. Ld1 rear bumper 2015-17 ford f150
Stampa la paginaIMPORTANT: On models with FORD "HD" tow package, the factory bumper features an
integrated receiver hitch and it cannot be reinstalled with the replacement Bumper, (Figure
3A). Bumper is compatible with models without receiver hitch, (standard tow package-Figure
3B), and with the FORD "MAX DUTY" tow package, (separate receiver hitch). Bumper is also
compatible with most replacement receiver hitches.
4. Select (1) Mounting Bracket, (Figure 5A). Attach the Bracket to the passenger side mounting
plate on the back of the bumper with the included (2) 12mm x 35mm Hex Bolts, (2) 12mm Lock
Washers and (2) 12mm Flat Washers, (Figures 5A & 5B). Snug but do not fully tighten at this
time. Repeat this Step to attach the Mounting Bracket on the driver side.
5. NOTE: Sensors, (if equipped), must be installed onto the back of the Bumper before installing
the Bumper to the vehicle.
Models without bumper sensors:
a. Select the included (4) Rubber Plugs.
b. From behind bumper, push plugs into sensor mounting holes.
Models with bumper mounted sensors:
a. Remove the small factory sealing washer from the sensor. Attach the provided larger (1)
Foam Washer onto the front of the sensor.
b. Push the sensor in from the back of the Bumper until it is flush with the sensor sleeve.
NOTE: Sensor tabs may need to be trimmed to fit sensor inside the sensor sleeve.
Attach the adhesive side of (1) Foam Spacer to (1) Retaining Ring. Push the Retaining
Ring into the sensor sleeve until it locks into the mounting holes, (Figure 6).
c. Repeat the previous steps to install each sensor to the back of the Bumper.
6. LED light installation at ends of bumper as supplied with bumper or sold separately.
a. Insert light into opening and up to mounting slots. Check for clearance between front
and back of light. If necessary, remove the screen from the back of the opening for
additional clearance or access to light, (Figure 7).
b. Follow the light manufacturer's instructions to attach (1) light to the center slot or (2)
lights to the inner and outer slots in the top of the light opening.
c. Repeat the above steps for passenger side light installation.
d. Follow light manufacturer's instructions to properly wire the light.
7. With assistance, position the Bumper Assembly up to the mounting flanges on the end of the
frame. Temporarily support the weight of the Bumper. WARNING: To avoid possible injury or
damage to the vehicle, do not proceed until the bumper is fully and safely supported.
8. Attach the Bumper Brackets to the ends of the frame with the included (6) 12mm x 50mm Hex
Bolts, (12) 12mm Flat Washers and (6) 12mm Nylon Lock Nuts, (Figures 8A & 8B). Do not
tighten hardware.
9. Level and adjust the bumper and fully tighten all hardware including the Mounting Bracket to
Bumper hardware.
10. Reinstall the license plate lights and trailer plug, (Figure 9). NOTE: Use a flat blade
screwdriver to carefully pry the metal clip on the plug out to grab the edge of the opening.
11. Use the included (2) push-in plugs to attach the license plate to the Bumper, (Figure 10).
12. Attach the wiring harness to the lights and trailer plug.
13. Use the included Wire Ties to secure the wiring harness to the bumper and frame as
necessary.
14. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap
may be used to clean the Bumper assembly.
Page 2 of 6
LD1 REAR BUMPER
2015-17 FORD F150
2/26/18 REV (RA)