Astivita ASEDW Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Lavastoviglie Astivita ASEDW. Astivita ASEDW 6. Domestic dishwasher

Stampa la pagina

Installation

Positioning the Appliance

Positioning the appliance in the desired location. The back should

rest against the wall behind it, and the sides, along the adjacent

cabinets or wall. The dishwasher is equipped with water supply

and drain hoses that can be positioned to the right or the left of

the appliance.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them

in or out) to adjust the level of the dishwasher. The appliance

should not be inclined more than 2˚. If it is level, it will help en-

sure proper performance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas)

connector, making sure that it is fastened tightly in place (see fig.2).

Some models are fitted with an "Aquastop" water supply hose

(see fig.1) in which the small filter is already housed in the

threaded end.

If the water pipes are new or have not been used for an extended

period of time, let the water run to make sure that the water is

clear and free of impurities. If this precaution is not taken, there

is a risk that the water inlet can get blocked and damage the

appliance.

Hot Water Connection

The water supply to the appliance can also be connected to the

house's hot water line (centralised system, heating system), as

long as it does not exceed a temperature of 60

In this case,the wash cycle time will be shortened by about 15

minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the

same procedures as those for the connection to the cold water

line.

fig.1

fig.2

Anti-Flooding Protection

The dishwasher is equipped with a system that stops the supply

of water in the event of a problem with the water supply hose, or

leaks within the unit, in order to prevent damage to your home. If

for any reason the box containing the electrical components hap-

pens to get damaged, remove the plug for the appliance from

the socket immediately. In order to guarantee that the anti-flood-

ing feature operates properly, the "A" box with water supply hose

must be attached to the water supply tap as shown in Fig .1. No

other type of connection is acceptable.

The water supply hose must not, under any circumstances, be cut,

as it contains electrical parts which are live. If the length of the hose

is not adequate to make a proper connection, the hose must be

replaced with one which is long enough. This hose is available upon

request from specialised retailers and service centres.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter

of 4cm, Or let it run into the sink, making sure to avoid bending

or crimping it. Use the special plastic support that comes with

the appliance (see fig.3). The free end of the hose must be at a

height between 40 and 100 cm and must not be immersed in

water.

Attention:

The special plastic hose support must be solidly fastened to the

wall to prevent the drain hose from moving and allowing water to

spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the

current in the home correspond to those on the rating plate

(located on the stainless steel inner door of the appliance) and

that the electrical system is correct for the maximum voltage on

the rating plate, insert the plug into an electrical socket which is

earthed properly (the earthing of the appliance is a safety re-

quirement mandated by law).

If the electrical socket to which the appliance must be connected

is not appropriate for the plug, replace the plug, rather than us-

ing adaptors or the like as they could cause overheating and

burns.

Caution:

The dishwasher plug must be accessible even when the appli-

ance is installed as a built-in unit so that maintenance can be

done safety.

.9.

Close-up View (Interior)

A Cup Rack

B Upper Rack

C Rack Height Adjustor

D Top Spray Arm

E Lower Rack

fig.3

F Bottom Spray Arm

Technical characteristics

Width

Depth

Height

Capacity

Mains water pressure

Power voltage

Total absorber power

G Washing Filter

H Detergent and Rinse Aid Dispenser

Silverware basket

J Knife rack

K Third Sprayer

.2.

60 cm

85 cm

12 standard place settings

0.03-0.6MPa

220-240V~ 50Hz

2150W