Donner DEK-610S Manuale d'uso - Pagina 7

Sfoglia online o scarica il pdf Manuale d'uso per Strumento musicale Donner DEK-610S. Donner DEK-610S 16.

backing voice will repeat the bar until the end of the song stops. Press "TEACH 1" or "START/STOP" button again to exit and

the LCD learning function is closed.

5. Teaching Function 2 (Following mode)

Press the key of "TEACH 2" and enter the following mode. The teaching function point of the LCD screen will be lit up. After

the song is played, the main melody will not be played. The user must press the key according to the corresponding

keyboard to continue to play the next note. The background sound will play the section repeatedly until the end of the song.

Press "TEACH2" again or press the "Start/Stop" button to exit the function and the LCD teaching function is closed.

6. Teaching Function 3 (Ensemble mode)

Press the "TEACH 3" key and enter the ensemble mode. The teaching function points of the LCD screen will be lit up. The

main melody does not play the flash and without prompting, the user will play the main melody keyboard by his own ability.

If you do not press the keyboard to play the main melody in about 7 seconds, it will play automatically. As long as you play

the main melody of the keyboard, it will be blocked until the end of the song. Press "TEACH 3" again or press the "Start/Stop"

button to exit the function and the LCD learning function is closed.

(IV). Use of recording and programming functions

1. Recording and playback

Press the "REC" key, and the LCD recording function will be lit up, playing the keyboard melody at this time you can record

the song notes. The song after playing and then press the "PLAY" key will just play the song from beginning to end, after the

playing, press the key one more time you can play the song just recorded again. To disable the recording and playback

functions, press the "Record" key or the "Start/Stop" key again.

Note: The recording can record a maximum of "85" notes. After the recording is full, the following notes will not be recorded.

Turn off the power and turn it on again, all the recorded data will be cleared.

2. Use of rhythm programming and programming playback

Press the "PROG" button, then the rhythm programming function of the LCD will be lit up. Press the 7 corresponding

percussion instruments on the panel, or press the "PERCUSSION" button to convert the keyboard into full keyboard

percussion. You can record the self-programmed percussion one by one (up to 32 drum beats can be programmed) by

pressing the keyboard corresponding percussion , and then press the "PLAYBACK" key after the programming is finished. At

this point, the piano will playback the percussion rhythm you just programmed. During rhythm playback, you can adjust the

playback speed by pressing "TEMPO+ "or "TEMPO-" key. To cancel the programming function, press the "PROGRAM" button or

the "Start/Stop" button again.

Note: If you use the keyboard drum percussion, press "Percussion" key again to cancel the full keyboard drum percussion,

and the full keyboard will switch to playing mode. Turn off the power and turn it on again, all the programmed data will be

cleared.

(V). Play with rhythm and auto accompaniment (styles)

1. Start of rhythm

Press the "START/STOP" button once to immediately start the rhythm accompaniment. At this time, the small dots in the

beat display area of the LCD will keep flashing, and the beat indicator will swing from side to side with different beats. To

turn off the rhythm, press the "Start/Stop" button again.

2. Intro and ending

Press the "INTRO" key during the rhythm playing, then the rhythm will stop playing after playing a short piece of the

endgame ; If you press the "ENDING" key when the rhythm is not started, the current rhythm will be played after a short

prelude. You can also press the "SYNC" key to play a single or multi-finger chord, intro/ending, and then press the chord

keyboard area (1 to 19 keys from the left) at the same time to start the prelude, or you can choose to play separately.

3. The choice of rhythm (Rhythm name refer to Appendix II: Rhythm unified table)

By default, tone selection is used when the system is powered on. Press the "RHYTHM" key to switch from tone selection to

rhythm selection. You can select the rhythm you want on the number key, and the number and name of the rhythm will be

displayed on the LCD. For example, select the rhythm numbered 18, press the number key "0, 1, 8" , at this time the LCD

digital displays "018" rhythm and its name. In rhythm selection mode, press the "+" key, or "-" key, the rhythm number

increases or decreases in sequence until you select the wanted rhythm.