DoorKing 1489-080 Istruzioni - Pagina 2

Sfoglia online o scarica il pdf Istruzioni per Controllore DoorKing 1489-080. DoorKing 1489-080 2. Wireless tracker expansion board rf kit

Stampa la pagina
Board Reference
See "Wireless System Layout and Start-Up Procedure"
for system layout limitations.
RF SECURE LED
UNPAIRED MODE:
Steady Red – Board is communicating with unpaired wireless baseboard.
Blinking Red – Board is NOT communicating with unpaired wireless baseboard.
PAIRED MODE:
Steady Green - Board is communicating with paired wireless baseboard.
Blinking Green - Board is NOT communicating with paired wireless baseboard.
Board Address (REQUIRED)
Connection to Wiegand 2: Addresses 03-10
Connection to Wiegand 1: Addresses 11-18
See HARDwire tracker expansion
board manual for more information.
RF Range
Adjustment
Set to max (full clockwise) for
most applications. This may
need to be dialed back to limit
the range when using a repeater.
Program Button:
Press after adjustment has been made to
•
the RF RANGE, RF ID or RF CH before
changes will take effect.
•
Press and hold for 3 sec. to PAIR to
wireless baseboard, may take up to 20
seconds to PAIR.
(RF SECURE LED Paired - steady GREEN).
•
Press and hold again for 3 sec. to UNPAIR
from wireless baseboard if necessary
(RF SECURE LED Unpaired - steady RED).
IMPORTANT Wiring and LED Note:
See HARDwire tracker expansion board manual for
terminal #1 - #34 connections and LED descriptions.
DO NOT connect any wires to terminals #10, #17,
#27, #28 and #29.
Programming
See the "HARDwired Installation/Owner's manual" for complete programming information for the tracker expansion board.
Important Notice
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be
totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a well-constructed network, DoorKing wireless products should not
be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of
property. DoorKing, Inc. accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using DoorKing wireless products, or for failure of
DoorKing wireless products to transmit or receive such data.
Safety and Hazards
Do not operate DoorKing wireless products in areas where cellular modems are not advised without proper device certifications. These areas include environments
where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio interference. DoorKing wireless
products can transmit signals that could interfere with this equipment. Do not operate DoorKing wireless products in any aircraft, whether the aircraft is on the ground or in flight. In aircraft,
DoorKing wireless products MUST BE POWERED OFF. When operating, DoorKing wireless products can transmit signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. DoorKing wireless
products may be used at this time.
The driver or operator of any vehicle should not operate DoorKing wireless products while in control of a moving vehicle. Doing so will detract
from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices
while in control of a vehicle is an offence.
1489-065-D-10-14 - Not for Release
RF
SECURE
RF
RF
BOARD ADDRESS
DATA
STATUS
ON
1
0
1
2
3
4
5
6
7
8
9
10
RF RANGE
11
12
PROGRAM
13
14
1489-010
15
16
17
18
19
20
LED Display
Programming
Buttons
Press
buttons or
ENT button to activate
LED display.
Copyright 2014 DoorKing, Inc. All rights reserved.
RF Data LED – Blinks when receiving a reply from
wireless baseboard after a card code is sent.
RF Status LED – Not used.
Code Sent LED – Blinks after a card code has been sent to wireless baseboard.
Code Good LED – Blinks if the card code is in the database (access granted).
Code Bad LED – Blinks if the card code is not in the database (access denied).
Antenna is REQUIRED.
Board Relay Jumpers
OUTPUT
ALARM
AUX
2358-010
CODE
CODE
CODE
RELAY
RELAY
RELAY
SENT
GOOD
BAD
NC
NC
NC
NO
NO
NO
RF
SYNC
RF
LOST
RF ID
RF CH
RF
STRENGTH
4
4
POWER
RESET
ENT
RESET Button - Press to reboot tracker expansion board
AND the 1489 wireless board.
2358 Tracker Expansion Board
1489 Wireless Board
DoorKing Part Number
1489-080
RF Strength LED:
Updated every time a RF SYNC signal is received.
Green - Strong signal - Normal
Yellow - Marginal signal - May lose communication.
Red - Poor signal - Unreliable
RF SYNC LED:
Blinking Blue - Connected with wireless baseboard.
Blinking Rapidly - Pairing with wireless baseboard.
21
OFF - No signal with wireless baseboard.
22
Note: If LED lights for a couple of seconds after the
reset button or program button is pressed, this indicates
23
this board has been programmed to forward card codes
24
for other boards (See program table).
25
RF LOST LED:
26
ON - Lost communication with wireless baseboard.
27
OFF - Communication is established with wireless
28
baseboard.
29
Blinking Rapidly - Pairing with wireless baseboard.
30
31
RF ID
RF CH
32
MUST be set to SAME
4
4
33
ID number and channel
34
number as the wireless
baseboard.
Power Transformer
Power transformer is
REQUIRED and is wired to
terminals #33 and #34, wire
polarity does not matter.
18 GA. Wire 100 ft max
16 GA. Wire 200 ft max
120 S. Glasgow Avenue
Inglewood, California 90301
Important
U.S.A.