Akw Option ZW Istruzioni per l'installazione

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Apparecchiature per il bagno Akw Option ZW. Akw Option ZW 2. Shower screens

Stampa la pagina

step 10

Re-glaze the panel using the two sizes 2 x 2 rubber

gaskets supplied.

Larger size for the wet side of the screen.

Push the gasket back into panel evenly on both

sides making sure the gasket finishes with outer

edge of compensators.

S S e e e e F F i i g g . . 1 1 3 3

GASKET SHOULD NOT BE STRETCHED.

CURTAIN RAILS ARE SUPPLIED OVERSIZE AND WILL NEED CUTTING TO SIZE

PLEASE FIT CORRECT AMOUNT OF HOOKS AND GLIDERS TO RAIL BEFORE INSTALLATION

step 11

Curtain rails are to be positioned on the

inside of the screens. Fit correct amount of

hooks and gliders before fitting to wall.

Inside fall

When rail is level, mark off curtain rail bracket

of tray

hole positions, then drill into wall with a No.10

masonary drill bit, fit red plugs and then fit with a

No. 8 x 1

pan screws and cover caps.

S S e e e e F F i i g g s s . . 1 1 5 5

1 1 6 6

& &

step 12

When the rail and post are level using bracket supplied,

drill into the post and rail using a 3.5mm drill bit and

fasten with No. 8 x

pan screws and finish off with

cover caps.

S S e e e e F F i i g g . . 1 1 7 7

Red plug

Cover caps

1 /2

No. 8 x 1

pan

1 /2

No. 8 x

pan

Fig. 15

Level Rail

3x No. 8 x

pan

Level Post

www.akw-medicare.co.uk

Fig. 14

Option TT/TTW/Z/ZW Shower Screens

READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION.

POWER SHOWERS ARE NOT RECOMMENDED FOR USE WITH AKW SHOWER SCREENS

Please use the table below. Pick which cubicle is to be installed and read all steps clearly before installation.

STEP.1

Option TT

Option TTW

Option Z

Option ZW

Fig. 16

step 1

Take out adjusting screws from inside

Level Rail

of compensator. Place compensator

against wall making sure edge of

compensator lines up over the inside

edge of tray.

S S e e e e F F i i g g . . 1 1 . . 1 1

hooks & gliders

Use the card template to align the

outside edge of the compensator to

the outside edge of the the tray.

For flush mounted trays use the notch

as a guide to align the compensator

with the outside edge of the tray.

S S e e e e F F i i g g . . 1 1 . . 2 2

step 2

Fig. 17

FOR WET FLOORING INSTALLATION ONLY.

Take out adjusting screws from inside of compensator.

Corner blocks must be trimmed to suit altro floor using a

heavy pair of scissors or a pair of snips then sanded down

to give a smooth finish.

Place compensator against wall and mark off hole position

when level. Drill into wall with a No.10 masonary drill bit.

Fit red plugs and fix compensator with No. 8 x 1

S S e e e e F F i i g g . . 2 2

07-002-403-02

Installation Instructions

Inside of screen must be fitted to inside flat area of the tray.

STEP.2

STEP.3

STEP.4

STEP.5

STEP.6

STEP.7

Compensator

Fig. 1.1

Outside edge

Inside edge

of the tray

Fig. 1.2

Compensator

Fig. 2

Floor covering

pan.

Floor

STEP.8

STEP.9

STEP.10

STEP.11

STEP.12

Wall

Compensator

No. 8 x 1

Pan

Fig. 1.3

Mark off hole position when level. Drill into wall with

a No.10 masonary drill bit. Fit red plugs and fix

pan. S S e e e e F F i i g g . . 1 1 . . 3 3

compensator with No. 8 x 1

Plaster

Wall

Brickwork

Corner Block