Flying Industry Development CV-4-3 Manuale rapido - Pagina 2

Sfoglia online o scarica il pdf Manuale rapido per Telecomando Flying Industry Development CV-4-3. Flying Industry Development CV-4-3 3. Rf wireless remote control radio controller / transmitter & receiver
Anche per Flying Industry Development CV-4-3: Manuale rapido (4 pagine)

Stampa la pagina
Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)
Press button ▲ of first row: motor of receiver 1 rotates in positive direction.
Press button ▼ of first row: motor of receiver 1 rotates in reversal direction.
Press button ▲ of second row: motor of receiver 1 stops;
motor of receiver 2 rotates in positive direction.
Press button ▼ of second row: motor of receiver 2 rotates in reversal direction.
Setting control mode Momentary: Only connect Jumper-1 (CN1)
Press and hold button ▲ of first row: motor of receiver 1 rotates in positive direction. Release button ▲ of first row: Motor stops.
Press and hold button▼ of first row: motor of receiver 1 rotates in reversal direction. Release button ▼ of first row: Motor stops.
Press and hold button ▲ of second row: motor of receiver 2 rotates in positive direction. Release button ▲ of second row: Motor stops.
Press and hold button▼ of second row: motor of receiver 2 rotates in reversal direction. Release button ▼ of second row: Motor stops.
Limit control terminals:
Limit control terminals S1 and S2 are normally open, you can connect limit switches or sensors (normally open type) to terminals S1 and S2, and
then you can use limit switches or sensors to stop the motor.
When motor rotates in positive direction, if connect two terminals of S1, the motor will stop automatically.
When motor rotates reversal direction, if connect two terminals of S2, the motor will stop automatically.
Wired control terminals:
You can connect manual switches, external devices or sensors (with low level output signal) to control the motor.
1) The manual switches:
You can connect manual switches to terminals "Signal 1+", "Signal 1-", "Signal 2+", "Signal 2-", then you can use manual switches to control the
motor.
When connect terminals "Signal 1+" and "Signal 1-", motor rotates in positive direction. And when disconnect "Signal 1+" and "Signal 1-", motor stops.
When connect terminals "Signal 2+" and "Signal 2-", motor rotates in reversal direction. And when disconnect "Signal 2+" and "Signal 2-", motor
stops.
2) Signal input:
You can connect external devices (with low level output signal) to terminals "Signal 1+", "Signal 1-", "Signal 2+", "Signal 2-", then the external
device's output signal can control the motor.
When the external device outputs low level signal to terminal "Signal 1-" and "Signal 1+", motor rotates in positive direction.
When the external device outputs low level signal to terminal "Signal 2-" and "Signal 2+", motor rotates in reversal direction.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com