Astro Pneumatic Tool 498K Manuale di avvio rapido

Sfoglia online o scarica il pdf Manuale di avvio rapido per Strumenti Astro Pneumatic Tool 498K. Astro Pneumatic Tool 498K 4. 0.498" shank thor air hammer/riveter

Stampa la pagina

Model:

498K

WARNING

Study, understand and follow all instructions provided

with this product. Read these instructions carefully

before installing, operating, servicing or repairing this

tool. Keep these instructions in a safe accessible place.

INTENDED USE OF THE TOOL

This tool is designed to be used with 0.498" shank

attachments made of sufficient grade material and

design for the specified use. Do not use this tool

outside of the designed intent. Never modify the

tool for any other purpose or use.

WARNING

Caution: To help prevent personal injury

• Use of this product can expose you to chemicals

including ethylene glycol, gasoline vapors and

engine exhaust, which are known to the State of

California to cause cancer, birth defects, or

reproductive harm. For more information, visit

www.P65Warnings.ca.gov. Always wear ANSI

approved safety equipment, safety glasses and

clothing when using this product. Study, understand,

and follow all instructions provided with this product.

Failure to read and follow all warnings and operating

instructions may result in damages and serious

injury or death.

• Always wear ANSI approved goggles when using this

product. (Users and By standers).

• Never use this tool for any application other than for

which it was designed.

• Only use accessories designed for this tool.

• Never alter or modify this tool in any way.

• Improper operation and/or maintenance of the tool,

modification of the tool, or use of the tool with

accessories not designed for it could result in

serious injury or death.

• Always select the correct accessories of the correct

size and design for the job that you are attempting to

perform.

• Always work in a clean, safe, well-lit, organized and

adequately equipped area.

• Do not begin repairs without assurance that vehicle

is in secure position, and will not move during repair.

BEFORE USE

When unpacking, check the parts diagram and part

number listing on page 4 to make sure all parts are

included. If any parts are missing or damaged,

please call your distributor.

DO NOT DISCARD – GIVE TO USER

Product Type:

0.498" SHANK THOR AIR

HAMMER/RIVETER

1 YEAR LIMITED WARRANTY

• Astro Pneumatic Tool Co. warrants our products to the

original user against defective material or workmanship

for a period of 1 year (except where noted on our price

schedule) from the date of 1st use. Astro reserves the

right to determine whether the product failed because of

defective material, workmanship or other causes and to

charge back for missing parts. Astro Pneumatic Tool

Co., at its discretion, will repair products covered under

this warranty free of charge. The distributor should

direct the original user to return the product (with the

exceptions listed below) with the distributor's name,

address, adequate proof of date of purchase or a copy

of warranty card, and a short note explaining the

problem. Failures caused by accident, alteration, or

misuse are not covered by this warranty.

• Astro Pneumatic Tool Co. or its authorized service

representatives must perform all warranty repairs. Any

repair to the product by unauthorized service represen-

tatives voids this warranty. The rights under this warran-

ty are limited to the original user and may not be trans-

ferred to subsequent owners.

• This warranty is in lieu of all other warranties, expressed

or implied, including warranties of merchantability and

fitness for a particular purpose. Some states do not

allow the exclusion of limitations of incidental or conse-

quential damages so the above limitations may not

apply to you.

PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING

1-800-221-9705 FOR INSTRUCTIONS

PRODUCT INFORMATION

• The most powerful automotive air hammer on the planet

• Accepts .498" shank size bits and most quick change

chucks, manufacturer is not responsible for resulting

broken air hammer bits

• Not for casual use, always wear ear and eye protection

• Requires a 3/8" air line, 6.2CFM, suggested use

with HI-FLO fittings

Specification:

Air inlet: 1/4"

Working pressure: 90PSI

Free Speed : 1140 BPM

Piston Dia. : 19 mm / 3/4"

Piston Stroke : 98.4 mm / 3-7/8"

Shank Dia. :12.6 mm / 0.498"

Page 1

www.astrotools.com

Air consumption: 6.2 CFM

Vibration value: 22.52 m/s2

Sound power: 94.4 dBA

Weight: 2.5 kg / 5. 5lbs

Overall length: 257mm / 10"