Flying Industry Development S4PXW-DC06-ANT3 Manuale rapido - Pagina 2

Sfoglia online o scarica il pdf Manuale rapido per Ricevitore Flying Industry Development S4PXW-DC06-ANT3. Flying Industry Development S4PXW-DC06-ANT3 4. 5000 meters rf wireless receiver

Stampa la pagina
Flying Industry Development S4PXW-DC06-ANT3 Manuale rapido
Release button C of the transmitter: Terminals OUT3 stop outputting.
Press and hold button D of the transmitter: Terminals OUT4 output DC power.
Release button D of the transmitter : Terminals OUT4 stop outputting
Setting control mode Latched (with transmitter CC-4): Move the second bit of the dip switch to the terminal "on".
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press button A of the transmitter: Terminals OUT1 output DC power, and other terminals OUT2, OUT3, OUT4 no output.
Press button B of the transmitter: Terminals OUT2 output DC power, and other terminals OUT1, OUT3, OUT4 no output.
Press button C of the transmitter: Terminals OUT3 output DC power, and other terminals OUT1, OUT2, OUT4 no output.
Press button D of the transmitter: Terminals OUT4 output DC power, and other terminals OUT1, OUT2, OUT3 no output.
Transmitters:
1) The receiver can only pair our CC and CCW series transmitters, such as model CC-4 (5000m), CCW-4 (5000m, waterproof).
2) You also can use four transmitters with one button to work with this receiver, and each transmitter will control receiver's a channel. Such as model
CC-1 (5000m), CCW-1 (5000m, waterproof).
Input control terminals:
The receiver has four input control terminals, you can connect external devices, sensors, or manual switches to these terminals to control the outputs
of receiver.
1) Signal input:
You can connect external devices (with low level output signal) to terminals "COM", "Signal 1", "Signal 2", "Signal 3", "Signal 4", the external device's
output signal can control receiver's four outputs.
When the external device outputs low level signal to terminal "COM" and "Signal 1", Terminals OUT1 output DC power.
When the external device outputs low level signal to terminal "COM" and "Signal 2", Terminals OUT2 output DC power.
When the external device outputs low level signal to terminal "COM" and "Signal 3", Terminals OUT3 output DC power.
When the external device outputs low level signal to terminal "COM" and "Signal 4", Terminals OUT4 output DC power.
2) The manual button:
You can connect four manual switches to terminals "COM", "Signal 1", "Signal 2", "Signal 3", "Signal 4", then you can use these manual switches to
control the outputs of receiver.
When connect terminals "Signal 1" and "Com", Terminals OUT1 output DC power. And when disconnect "Signal 1" and "Com", Terminals OUT1 stop
outputting.
When connect terminals "Signal 2" and "Com", Terminals OUT2 output DC power. And when disconnect "Signal 2" and "Com", Terminals OUT2 stop
outputting.
When connect terminals "Signal 3" and "Com", Terminals OUT3 output DC power. And when disconnect "Signal 3" and "Com", Terminals OUT3 stop
outputting.
When connect terminals "Signal 4" and "Com", Terminals OUT4 output DC power. And when disconnect "Signal 4" and "Com", Terminals OUT4 stop
outputting.
Feedback function:
If you press the button on the transmitter, the transmitter will send a signal to the receiver. When the receiver gets the signal from the transmitter, it
will been activated, and it will immediately send a feedback signal to the transmitter. When the transmitter receives the feedback signal, the
transmitter will exude a buzzing sound like "D~" which means the receiver is been activated successfully.
The working range:
With a transmitter to form a complete set, the distance can reach 5000m which is the longest distance of the transmitter. The distance of 5000m is a
theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other
constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or may not reach 5000m.
The receiver will have farther working range with external magnetic sucker antenna.
How to pair the transmitter to the receiver:
1) Press button K1 of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes twice, it means learning is successful.
Delete all transmitters:
We have learned the transmitter to the receiver. If you don't want the receiver to work with the transmitter, you can delete all codes of transmitters
which are stored in the receiver.
Operation: Press and hold the button K1 of receiver until signal LED flashes three times. That means all stored codes have been deleted
successfully.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com