Astroflex Astrostart RS-304 Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Avviamento a distanza Astroflex Astrostart RS-304. Astroflex Astrostart RS-304 4.

Stampa la pagina

UNLOCK DOORS AND DISARM WITH SIREN ACKNOWLEDGE (3 C)

(horn: 0, parking lights: 2, siren: 2)

UNLOCK DOORS AND DISARM WITHOUT SIREN ACKNOWLEDGE (1 C)

(horn: 0, parking lights: 2, siren: 0)

This command will unlock all doors (optional interface), and

disarms the alarm. The LED stops flashing.

If the alarm is triggered during your absence, the

ASTROSTART™ will acknowledge by (horn: 2) when your

disarm the alarm. If you wish to know the nature of the

violation, check the code displayed on the main switch LED.

PASSIVE MODE

TO ARM PASSIVELY

The system automatically arms when you turn OFF the

ignition key and leave your vehicle as you would normally.

The system will arm 20 seconds after last door is closed.

There is no confirmation by the ASTROSTART™ ( parking

lights 0,

horn 0). The LED will flash code 1 to indicate armed status.

Opening any door during the exit delay restarts the delay

after the door is closed again. When arming passively, the

ASTROSTART™ will bypass any zone that shows a violation

(ex. hood left open). The horn and parking lights will

acknowledge five (5) seconds after last door is closed (horn:

1, parking lights: 1, optional siren:0

TO DISARM PASSIVELY

When the alarm has been armed passively, disarm by turning

ignition key to the RUN position before the end of a 30

second entry delay (or 15 seconds, dealer programmable). If

the ignition key is not put in the RUN position within 30

seconds (or 15 seconds) of opening the first door, the alarm

will trigger (horn: 1, parking lights:1, optional siren:1). If this

happens shut the alarm off by turning the ignition key to the

RUN position or entering (1 C) on the transmitter.

* Entry delay time is programmable (the factory preset is 30

seconds). Refer to the "User Programming" section."

TO ARM ACTIVELY BY REMOTE (1 B, OR 3 B)

Arming by remote in the passive mode is possible. Entry and

Exit delays are cancelled and alarm operation is the same as

when in active mode. Disarming by remote is then necessary

(for further details, refer to "Active mode" section). The

following combinations are possible in passive mode:

•

arm and disarm passively

•

arm passively and disarm actively (with the transmitter)

•

arm and disarm actively (with the transmitter)

AUTOMATIC RE-ARMING

Your ASTROSTART™ alarm system includes an Automatic

Re-arming feature. If the system is triggered while you are

away from the vehicle it will automatically re-arm after going

throug the alarm cycle.

LOST OR BROKEN REMOTE CONTROL

If you have lost or broken your remote control and the alarm

system is armed:

•

In less than 30 seconds,

Get into your vehicle (the alarm will sound)

turn ignition key to "ON" position (not "START")

leave your vehicle and close all doors.

•

Patiently wait TWO minutes without disturbing the

vehicle, until the alarm is silent.

•

The ASTROSTART™ switches into passive mode. From

now on, only the ignition key is required to arm/disarm the

system. See the section on "PASSIVE MODE" for more

information.

Ask your ASTROSTART™ dealer to repair or replace

your transmitter as soon as possible.

WHAT TRIGGERED THE ALARM?

The alarm will store the last zone which triggered the alarm.

Refer to the Infraction Code Description" chart for proper

zone description.

RS-304 ALARM INFRACTION CODES

BLINKS ALARM CONDITION

Normal operation. Alarm is armed.

Door was opened

Hood was opened

Internal shock sensor was tripped

Ignition key was ON (only in active arming mode)

Other sensor input was tripped.

DOOR LOCKING AND UNLOCKING

This optional interface allows you to control by remote several

vehicle electrical system options. This interface is optional

and will require the purchase of additional equipment (see

your dealer). The following systems can be controlled:

•

Electronic door lock system.

•

Electronic trunk/hatch release.

COMMANDS

LOCK AND ARM WITH SIREN ACKNOWLEDGE (3 B)

This command locks all doors and arms the

ASTROSTART™ alarm. (horn:0, parking lights:1, siren:1).

LOCK AND ARM, WITHOUT SIREN ACKNOWLEDGE (1 B)

This command locks all doors and arms the

ASTROSTART™ alarm. The alarm siren remains silent.

(horn:0 , parking lights: 1, siren: 0).

UNLOCK AND DISARM WITH SIREN ACKNOWLEDGE (3 C)

To unlock all doors and disarm the ASTROSTART™ alarm.

(horn: 0, parking lights: 2, siren: 2).

UNLOCK AND DISARM, WITHOUT SIREN

ACKNOWLEDGE (1 C)

This command unlocks all doors and disarms the

ASTROSTART™ alarm. The optional alarm siren remains

silent. (horn:0, parking lights:2, siren:0).

LOCK, WITHOUT ARMING (2 B)

To lock all doors without arming the alarm. (horn:0 , parking

lights: 1, siren:0)

OPEN TRUNK, UNLOCK AND DISARM WITH SIREN

ACKNOWLEDGE (2 C)

This command unlocks all doors, disarms the

ASTROSTART™, and releases the trunk with a siren

acknowledge (horn: 0, parking lights: 2, siren: 2)

AUXILIARY OUTPUT (3BC)

Connection of this output is optional and is highly flexible to

adapt to various needs.Consult your local ASTROSTART™

dealer for typical applications.

TEMPORARILY DISEABLE SHOCK SENSORS (3B&A)

This command disable all shock sensors. (horn: 0, parking

light: 4, siren: 0). The shock sensors will be re-enable when

pressing the brake pedal.

USER PROGRAMMING

Your ASTROSTART™ system is designed to provide the

ultimate convenience and flexibility. There are several options

that you as the owner have in controlling how your system

works. These options are selected in the "User Programming

Mode". Refer to the "User Programming Codes" for a listing

of all options and factory pre-sets. If you wish to change any

parameters, follow this procedure in entering and exiting the

"User Programming Mode"

1) TO ENABLE THE TRANSMITTERS PROGRAMMING

MODE

Push "P" four (4) times

The GREEN LED illuminates

Push "A,B,C" simultaneously The RED LED should now be

flashing rapidly, the system will

remain in the "User Programming

Mode" for five (5) minutes.

2) TO ENABLE THE MODULES PROGRAMMING MODE

(UNIT INSTALLED IN VEHICLE)

•

Turn the main system switch OFF.

•

Turn the ignition key to the ON position.

Do not start the engine.

•

Turn the main system switch ON.

•

Turn the ignition OFF.

The parking lights will flash four times to acknowledge.

Programming commands can now be entered through the

remote control ( refer to the programming chart below). Exit

the programming mode by depressing the brake pedal.

Push "P" four (4) times

The GREEN LED illuminates

Push "A, B, C"

simultaneously again

RED LED will flash slowly and turn off).