Dorma RTS Series Manuale di avvio rapido
Sfoglia online o scarica il pdf Manuale di avvio rapido per Per serrature Dorma RTS Series. Dorma RTS Series 2. Side load wood door and frame
Anche per Dorma RTS Series: Manuale di avvio rapido (2 pagine), Manuale di avvio rapido (2 pagine), Manuale di avvio rapido (2 pagine), Manuale di avvio rapido (2 pagine), Manuale di avvio rapido (2 pagine), Manuale di avvio rapido (2 pagine)
Stampa la pagina
RTS SERIES PACKAGE 03
SIDE LOAD STEEL DOOR AND FRAME
1. PREPARE FRAME AND INSTALL CLOSER
NOTE: 8532 mounting channel is to be
installed prior to frame installation.
Prepare header 1 according to template.
Fasten angle bracket 2 to closer 3
with two hex head machine screws and flat
washers. Install two fillister head
machine screws 4 into mounting tabs on
closer, make approximately three turns.
Install closer into mounting channel 5
in header 1 by inserting mounting tabs
into mounting bracket, then raise end of
closer with angle bracket 2 onto the
two 1/4-20 screws installed in mounting
channel 5 . Fasten angle bracket to the
remaining 1/4-20 screws with lock washers
and nuts 6 . Tighten the two fillister
head machine screws. SECURELY!
Install cover plate 7 by sliding tab
into frame and fasten opposite end to
mounting bracket with two 8-32 flat head
machine screws provided.
2. PREPARE TOP OF DOOR AND INSTALL CLOSER ARM
Prepare top of door according to template.
NOTE: Cut-out side of door should face
interior of building. Fasten adjustment
stud 8 to door channel. Install two
1/4-20 hex head alignment screws 9 into
closer arm 10 . Place closer arm 10
over adjustment stud 8 in door channel.
Center arm in door, turn 1/4-20 hex head
alignment screws 9 counterclockwise until
they are wedged against door channel. Thread
lateral adjustment screw 11 into adjustment
stud 8 . Secure arm 10 into place with
1/4-20 flat head screw and flat washer 12 .
3. PREPARE BOTTOM OF DOOR, INSTALL ARM AND
FLOOR BEARING
Prepare bottom of door according to template.
Fasten arm 13 to door with five 1/4-20 flat
head machine screws. Prepare floor according
to template. Fasten floor portion 14 with
three flat head wood screws and plastic
anchors: OPTIONAL SEE TEMPLATE FOR THRESHOLD
PREPARATION.
4. INSTALL DOOR
With door parallel to opening, place bottom
of door onto floor bearing. Push door to
vertical position until closer spindle is
completely engaged into closer arm 10 .
Fasten clamping block 15 to arm 10 with
three 1/4-20 socket head cap screws 16 .
NOTE: Alternate fastening screws when
tightening clamping block. TIGHTEN SECURELY!
Fasten cover plate 17 to door with screws
provided.
www.dorma-usa.com
1-800-523-8483
5. ADJUST CLOSING SPEEDS
Valve "A" - Controls closing speed from
maximum opening angle to 0° , clockwise turns
decrease closing speed, counterclockwise
turns increase closing speed.
Valve "B" - Increases closing speed from
maximum opening angle to 20°, turn valve
counterclockwise.
VALVE "B"
6. DOOR ALIGNMENT
Double Acting - Center door in frame by
loosening 1/4-20 flat head screw 12 and
adjusting the 1/4-20 hex head alignment
screws 9 as required. To adjust
clearances between door and frame, adjust
lateral adjustment screw 11 . Retighten
1/4-20 flat head screw 12 . TIGHTEN
SECURELY!
Single Acting - To insure that door closes
tightly against stop, adjust top arm as
follows. Loosen the 1/4-20 flat head
screw 12 , adjust arm fully in the
direction of door swing. Retighten 1/4-20
flat head screw 12 .
7. CLEARANCE REQUIREMENTS
The standard spindle for 7471K will achieve
a door clearance of 11/16" measured from
finished floor to bottom of door. See
chart on template for optional spindles
and door clearances.
8. DOOR REMOVAL
Remove cover plate 17 from side of door.
Remove clamping block 15 from top arm.
Lean top of door out until it clears frame.
Lift door off of floor bearing 14 .
INSPK NO. 08280300 Rev.12/08
08280301
PAGE
INS NO.
VALVE "A"
"A"
"B"
1 of 2
12/08
Rev.