Canyon 98-161 Manuale di istruzioni per il montaggio - Pagina 13
Sfoglia online o scarica il pdf Manuale di istruzioni per il montaggio per Arredamento per interni Canyon 98-161. Canyon 98-161 14. Cottage colors collection bunk bed
Stampa la pagina
LIST OF CONTENTS
COTTAGE COLORS COLLECTION
BUNK BED TOP END BOX ( 98-705 ) FIG.1 (2 BOXES)
A.- (1) TOP BUNK BED END
HARDWARE PACK (HPK00012)
B.- (2) METAL DOWEL PINS
6 DRAWER DRESSER BOX ( 98-208 ) FIG.2
C.- (1) 6 DRAWER DRESSER
3 DRAWER COMPUTER DESK BOX ( 98-602 ) FIG.3
D.- (1) COMPUTER DESK
6 PCS SIDE RAILS BOX ( 98-730 ) FIG.4
E.- (4) SIDE RAILS
F.- (2) GUARD RAILS
HARDWARE PACK
G.- (24) 80MM FLAT HEAD BOLTS
H.- (24) 5/8" CROSS DOWEL NUTS
I.- (1) 5MM ALLEN WRENCH
LADDER BOX ( 98-720 ) FIG.5
J.- (1) LADDER
HARDWARE PACK
K.- (2) METAL HOOK BRACKETS
L.- (6) 1" SCREWS
TWIN/FULL BED BOX ( 98-707,98-709 ) FIG.6
M.- (1) HEADBOARD
N.- (1) FOOTBOARD
4 PCS SLAT PACK BOX ( 98-645,98-646 ) FIG.7
O.- (4) SLATS
HARDWARE PACK
P.- (8) 1 1/4" SCREWS
1.- TO ASSEMBLE THIS BUNK BED, USING TWO TOP BUNK BED ENDS (A), ONE 6 DRAWER DRESSER (C), ONE COMPUTER DESK (D), TWO SIDE RAILS (E) AND TWO GUARDRAILS (F).
2.- REMOVE FACTORY INSTALLED PLASTIC PLUGS FROM THE TOP OF DRESSER AND THE TOP OF THE DESK, THEN INSERT ONE METAL DOWEL PIN (B) IN EACH HOLE OF THE TOP, TAKE THE TOP BUNK BED END (A)
PLACE IT ON TOP OF THE DRESSER & DESK WITH THE GROVE LINES FACING LIKE FIG.8, ALIGNING THE METAL DOWEL PINS WITH THE BOTTOM HOLES OF TOP BUNK BED END UNTIL ARE ALL THE WAY IN, SEE FIG.8
3.- INSERT TWO CROSS DOWELS (H) IN ACCESS HOLE INSIDE THE SIDE RAIL & GUARD RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9
4.-ATTACH TWO SIDE RAILS (E),TWO GUARD RAILS (F) TO BOTH TOP BUNK BED ENDS (A),INSERTING TWO 80MM FLAT HEAD BOLTS (G) INTO TOP BUNK BED END HOLES,USE THE 5MM ALLEN WRENCH (I) TO TIGHTEN
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),
BOTH FLAT HEAD BOLTS
5.- PLACE FOUR SLATS ( O) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH TOP BUNK BED ENDS, PUSH THE SLATS AGAINST THE BED END POST ( FIG. A ) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE FROM
THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (P), SEE FIG.11
FIG. 8
TO ASSEMBLE THIS BUNK BED REQUIRES TWO
MAKE SURE ALL BOLTS ARE TIGHTENED
REV 01 08/08/16
CANYON FURNITURE COMPANY.
( 98-705 ) COTTAGE COLORS COLLECTION BUNK BED ASSEMBLY INSTRUCTIONS
FIG.1
E
(HPK00104)
J
(HPK00008)
PHILLIPS HEADSCREWDRIVER (NOT INCLUDED)
(HPK00016)
YES,
HORIZONTAL GROOVE
FIG. 9
PERSONS
COMPLETELY
B
A
FIG.2
F
K
M
L
FIG.5
TOOLS NEEDED
5MM ALLEN WRENCH ( INCLUDED )
REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.10
( USE ONE 4 PCS SLAT PACK (98-645) )
NO
FIG. 10
PAGE 1 OF 2
C
FIG.3
G
FIG. 4
N
FIG.6
TIPS : SEE ILLUSTRATION BELOW
1.- USE THE LONG
END OF THE ALLEN WRENCH (Q) TO FASTEN
BOLTS LOOSELY AND QUICKLY.
2.- USE THE SHORT END OF THE ALLEN WRENCH FOR FINAL
AS SHOWN IN FIG.C
TIGHTENING
D
H
I
O
P
FIG.7
FIG. 11
FIG. A
KIS01131