Dot-Spot clarios-mini Manuale dell'operatore - Pagina 11

Sfoglia online o scarica il pdf Manuale dell'operatore per Attrezzature per DJ Dot-Spot clarios-mini. Dot-Spot clarios-mini 15.
Anche per Dot-Spot clarios-mini: Manuale dell'operatore (20 pagine)

Stampa la pagina

Safety

Safety instructions

During installation, the relative safety regulations have to be followed. The spot is operated

with protective low voltage of 12 V DC. To avoid danger and failures, prior or any work at

the spot or installation, disconnect the power supply from the mains. The spot can't be

opened. Connect the spot only to power supplies with a maximum output voltage of 12 V DC. A

wrong voltage may destroy the spot and the power supply.

Observe the installation manual of the power supply. Do not overload the power supply! The overall

power consumed by all consumers connected to the power supply should be approx. 10% lower

than the rated power of the power supply being used.

In order to protect the exposed connection cable from rodents it should be protected against mar-

tens (see installation accessories).

High ambient temperatures shorten the life of the LED's. Ensure a good heat dissipation in order to

guarantee a long life of the LED. During operation, do not expose the spot to ambient temperatures

of > 45°C. Do not cover the spot, provide free air circulation.

Do not open the housing of the luminary. The tightness of the clarios-mini is only guaranteed if also

the outer sheath of the connection cable is undamaged and if the connection cable is bonded in a

waterproof way. Otherwise, because of the capillary effect, the penetrating moisture can reach and

destroy the electronics of the spot.

Assembly

Preparation

Unpack all the parts included in the scope of delivery and check them for completeness and in-

tactness. Dispose of the packaging material no longer needed in accordance with applicable reg-

ulations.

If you notice any damage from transport, immediately contact the dealer where you purchased the

luminary.

Mechanical installation

Mark the hole for substrate mounting through the hole in base of the mounting bracket. The dowel

included in the scope of delivery is suitable for installation in concrete, stone and masonry. Drill a

hole of Ø 8 mm and deeper than 50 mm into the substrate and insert the dowel into the hole. In

case of wooden substrates the mounting bracket can directly fixed using the supplied screw, with-

out the dowel. In case of hardwood the holes may require pre-drilling with Ø 3 mm.

Position the mounting bracket over the dowel, orientate it into the desired direction and screw it

down with the supplied screw.

Now, the clarios-mini can be attached to the mounting bracket.

Assembly

Mechanical installation

■ Thread the snap ring onto the screw, insert it through the hole at the upper end of the mounting

bracket, thread the plastic washer onto the screw and screw it laterally into the threaded hole

on the luminary housing. In order to do so, keep the spot on the mounting bracket.

■ Pay attention to correct sorting: screw head, snap ring, mounting bracket, plastic washer,

luminary housing.

■ Orientate the spot in the desired direction and screw it tight with a 4 mm hex key.

Installation using the ground spike

Drive the ground spike into the ground using a suitable tool. When using a metal hammer, please

put a piece of wood or the like between the hammer and the ground spike in order to protect the

latter. Then, screw the mounting bracket with the luminary onto the ground spike using the screw

and the snap ring provided with the ground spike. The snap ring is placed between screw head and

mounting bracket. Orientate the mounting bracket before screwing it down.

Installation using the mounting extension

The mounting extension is designed for the use with the ground spike. Mounting extensions can be

combined.

Screw the mounting extension onto the ground spike using the threaded pin. Screw tight the mount-

ing extension: in order to do so, use a pair of pliers and put a cloth or the like around the mounting

extension.

Then, screw the mounting bracket with the luminary onto the mounting extension using the screw

and the snap ring provided with the ground spike. The snap ring is placed between screw head and

mounting bracket. Orientate the mounting bracket before screwing it down.

Installation of other accessories

During the installation of other accessories, refer to the respective installation instructions attached.

Electrical connection

Attention:

The design of the complete system and of the required power supplies must be carried

according to the protective low voltage SELV prescriptions!

The clarios-mini is supplied with DC power and dimmed via a separate PWM signal (pulse width

modulation). A PWM signal (S-PWM) is required for each light color. The PWM input has the following

characteristics:

PWM line connected to ground (-)

PWM line open

PWM line connected to operating voltage (+)

PWM frequency = 0 to 1,000 H

LED on

LED off