Boots Smooth skin Manuale di istruzioni per l'uso - Pagina 5
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Prodotti per la cura della persona Boots Smooth skin. Boots Smooth skin 17.
Stampa la pagina2. Warnings and Safety information continued
Electrical warnings
The Boots Smooth Skin system is designed
for use in the UK and elsewhere in the world
where the mains supply voltage is 100V to 240V
AC 50/60 Hz. Use on other supply voltages may
result in damage to the equipment.
After 50 shots in quick succession there is an
automatic cooling delay of about a minute where
the system will not respond—this is absolutely
normal and nothing to worry about. This cooling
delay is indicated by the 'READY' light flashing.
When it glows constantly the unit is ready to
use again.
After 200 shots within a 30 minute period there
will be a 5 minute automatic cooling delay where
the unit will not respond—this is absolutely
normal and nothing to worry about. This cooling
delay is indicated by the 'READY' light flashing.
When it glows constantly the unit is ready to
use again.
The unit will automatically go into STANDBY if
not used for approximately 1 minute, and the
green STANDBY light will come on. To use again
press the STANDBY button.
Check that the voltage rating marked on the
rating plate of the Boots Smooth Skin system
corresponds to the actual supply voltage.
Check that your Boots Smooth Skin system is
in good condition. Regular after use cleaning is
essential to maintaining the Boots Smooth Skin
system in optimum working condition.
8
do noT use if damage is found e.g. cracked
case, handset cable damage (internal wires
visible), cracked or badly chipped glass on the
handset etc. Internal parts contain energy levels
and voltages that are hazardous.
do noT use the Boots Smooth Skin system
in a bathroom or near sinks or other vessels
containing water. If the Boots Smooth Skin
system becomes wet it should not be used.
do noT coil the power cable around the power
supply during storage; this can lead to cable
damage and early failure.
do noT pull the handset cable tight, bend it
through very sharp angles or wrap it around the
unit for storage, this may cause cable damage
and early cable failure.
do noT use if either the base unit or hand unit
become hot to touch.
do noT dismantle; the Boots Smooth Skin
system contains no user-serviceable parts
and internal energy levels and voltages
are hazardous.
do noT use a power supply or any other
accessory unless they are specifically approved
and supplied for use with the Boots Smooth
Skin system. Use of accessories, which are not
approved, may be dangerous.
The Boots Smooth Skin system is designed to
operate between 15 – 30˚C.
AlWAyS unplug the Boots Smooth Skin system
when not in use.
3. Getting ready for a treatment
The Boots Smooth Skin system consists of three parts; the power supply, the base unit and the
handset. Each time you use the Boots Smooth Skin system, inspect all parts of the system for
damage. If damage is found it should not be used.
1. Power Supply
2. Base Unit
Gathering together the essentials
you may need
Before starting to use Boots Smooth Skin
system you may find it useful to gather together
some helpful bits and pieces.
You will need:
• Boots Smooth Skin Activator Gel
We recommend you keep this in the fridge so it's
more cooling when you apply it to the skin.
We recommend you have to hand:
• SPF30 fragrance-free sun tan lotion
• Aloe Vera gel
• Fragrance-free moisturising cream
• White eyeliner pencil
• White card or white sticky labels
• Spatula
• Tissues
• Towel
3. Handset
Set up the Boots Smooth Skin system
Place the base unit on a firm, flat surface.
The handset should be plugged into the base
unit taking care not to damage the retaining
clips and to fit the plug the correct way round.
Retaining clips
one on each side
do noT force the plug into the socket as this
may cause damage.
9