AmpliVox S505 Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Sistema di leggio AmpliVox S505. AmpliVox S505 4. Executive column sound lectern
Anche per AmpliVox S505: Manuale d'uso (4 pagine)

Stampa la pagina

OUR LECTERN MAY NOT CONTAIN ALL OF THE ELECTRONIC MODULES AS SHOWN AND EXPLAINED HERE

CONTROL PANEL

•

MIC 1: Adjusts volume level of gooseneck microphone on

reading table.

•

MIC 2: Adjusts volume level of microphone plugged into the

MIC 2 input jack on amplifier.

•

AUX: Controls output level of device that is plugged into the

L/R RCA jacks.

•

BASS: This control cuts or boosts the bass level.

•

TREBLE: This control cuts or boosts the treble level.

16 CHANNEL WIRELESS RECEIVER

• Channel Display (A)

• RF - Radio Frequency Indicator (B)

• AF - Audio Frequency Indicator (C)

• ASC / IR Auto Channel Select (Handheld Only) (D)

• Select Buttons - Manual Channel Selection (E)

• Mute Level Adjustment (F)

• Volume Control (G)

RECEIVER / TRANSMITTER (BODYPACK) SETUP

•

The receiver has its own

Power On. A Frequency Channel will appear in the Channel

Display (A). Press Select Buttons (E) to select a channel. Chan-

nel number must match channel number on wireless transmitter.

•

The

TRANSMITTER BODYPACK

alkaline battery. Slide off battery cover (H) and install battery as

shown. Make certain the battery is fully seated in its compart-

ment so the cover slides in place easily. Battery life with alkaline

batteries is approximately 8 hours of operating time.

Battery Cover

Channel Selector

control (G). Turn

POWER

VOLUME

is operated by 1 - "AA" 1.5 Volt

Top Panel

•

Select a channel (1-16) on side panel (I) of bodypack using the

supplied screw driver to select channel number. Channel select-

ed should match channel on receiver. When transmitter and

receiver are set to correct channel the

red when transmitter is turned on.

•

Plug the Lapel / Headset microphone into the

The lapel microphone can be clipped to a necktie or other cloth-

ing, using the supplied clip. The lapel mic should be placed under

the chin, as close to the center of the body as possible.

•

Slide the power

INDICATOR LIGHT

this LED turns red.

●

MUTE LEVEL ON RECEIVER

the factory. If speaker sound is breaking up, turn level clockwise

with small screwdriver until condition improves.

WIRELESS HANDHELD MICROPHONE—MODEL S1695

BATTERIES

Install batteries as follows;

•

Hold the body of microphone

in hand and twist off bottom

section of microphone.

•

Insert two "AA" 1.5 V batteries.

•

Twist bottom section back on to

microphone.

BATTERY STATUS

The life expectancy of the two batteries is about 10 hours. When the

"BATTERY" symbol on the display screen keeps flashing the batteries

should be replaced immediately.

AUTO SYNC

TO RECEIVER

First select channel you wish to use on the receiv-

er. Then press the ASC button (D), the IR light will

start to flash. Turn on microphone and point end

(M) of microphone at the flashing IR light on re-

ceiver and the microphone will auto sync to the

same channel as selected on the receiver.

RF INDICATOR

switch (J) to the

OFF

(L) will illuminate green. Replace batteries when

(F) is set at half way mark when it leaves

Functions

1) Interchangeable Microphone Head

2) LCD Screen

3) Power / Mute Control Switch

4) Select Button

5) 5) Microphone Input Sensitivity Adjust-

ment—is used to set the gain of microphone.

If you are a soft talking speaker you will need

to turn the control counter clockwise. Turn

clockwise if you are a loud talker. Use plastic

screwdriver that is supplied.

(B) will glow

(K).

MIC INPUT JACK

position, the

LED

ONTINUED NEXT PAGE