Amseco VDP-100 Manuale di istruzioni e manuale d'uso - Pagina 6

Sfoglia online o scarica il pdf Manuale di istruzioni e manuale d'uso per Sportello di cassa Amseco VDP-100. Amseco VDP-100 7. Video-eye people counter

Stampa la pagina

Installation Procedures

2) Installation of the Video Sensor Unit

Step 1) Refer to page 5 and decide the position to install the Video Sensor Unit.

Step 2) Pass the 4-pin Connector and Video Connector

through the holes in the mounting bracket. Make a

hole by removing the tab on the intended side of the

bracket for wire-through if necessary. You can

connect the Video Connector with your monitor

if you want to use the VDP-100 as a monitoring

camera.

2P VIDEO

4P CONNECTER

CONNECTOR:

Connect to the

monitor's VIDEO IN

(Optional)

MOUNTING

BRACKET

Step 4) Connect the 4-pin connector and video

connector to the Video Sensor Unit by snapping

them in until it is secure.

CLICK!!

Step 6) Pull the wires to the Counter Display Unit and move to the Counter Display Installations stage.

3) Installation of the Counter Display Unit

Step 1) Decide a place to install the Counter Display within the reach of a Power Source.

WARNING: PLEASE INSTALL THE COUNTER DISPLAY CLOSE TO THE VIDEO SENSOR UNIT SO

THAT THE WIRE LENGTH BETWEEN THE UNITS DOES NOT EXCEED 300 FEET.

(AWG # 20 OR LARGER GAUGE WIRES ARE REQUIRED FOR CONNECTIONS OVER 300 FEET.)

Step 3) Using the two screws provided,secure the

Mounting Bracket at the location that the Video

Sensor Unit is to be installed. (Refer to the Plan the

Installation on page 5 to decide an optimal

position for the Video Sensor Unit.)

DOOR

direction

BOLT SCREWS

BE CAREFUL FOR THE DIRECTION OF BRACKET

INSTALLATION WHEN MOUNTING ON THE CEILING

Step 5) Secure the Mounting Bracket and the Video

Sensor Unit by sliding the unit into the guide rails of

the bracket until it is secured. Make sure the round

part of the Video Sensor Unit is facing the door.

CLICK!!

DOOR

direction

Installation Procedures

Step 2) Open the front panel of the Counter Display

shifting the screw up at the bottom of the unit.

WARNING: DO NOT PLUG THE TRANSFORMER INTO AC OUTLET AT THIS TIME

WARNING: FOR ADDITIONAL EXTENSIONS OF POWER CORDS USE ONLY WIRES OF

AWG # 22 OR ABOVE.

Step 5) Remove the tab on the bottom of the Counter

Display if necessary to arrange the wires, and Secure

the Counter Display to the intended location using two

screws provided.

Close the cover and secure it with the screw.

4) Turning ON / Testing the System

Step 1) Plug-in the AC Transformer to AC outlet and turn the in-line switch ON. Make sure the red LED of

the Video Sensor Unit and LED display of the Counter Display is ON upon turning on the system.

Check the wiring and power sources if it is not.

Step 2) Walk across the detection area and check whether the counter and chime sounds are

working. (Ding-dong on ENTRY / Ding on EXIT) Adjust the angle of view a bit if necessary. Check

over the installation procedures and precautions in this Instruction Manual if the system does not

work properly.

WARNING: VDP-100 SHOWS ITS BEST PERFORMANCE WHEN THE VIDEO SENSOR UNIT

IS INSTALLED IN PARALLEL WITH THE FLOOR SO THAT THE CAMERA HAS A BIRDS-EYE

VIEW ON THE AREA. DO NOT ADJUST THE ANGLE UNLESS IT IS NECESSARY.

Step 3) Refer to page 9 of this manual, and adjust the chime volume and other user options if

necessary.

Step 4) Now your VDP-100 Video-Eye People Counter

Step 3) Using the 6-ft. Power Cord with in-line-switch,

connect the pre-stripped wires to the 12V AC 20VA

transformer terminals. Strip the insulation on the

opposite ends of the wires approximately 1/4 inch,

and insert into the terminals on the Counter Display

marked AC12V INPUT.

Step 4) Refer to the Wiring Diagram on page 8, and

connect the end of the 4-pin Connector Cable to the

terminals on the Counter Display.

RED

+12V

BLACK

(-)

ORANGE

EXIT

BROWN

ENTRY

WHITE

Tab

is ready.