Electrolux BM Series Manuale d'uso - Pagina 14
Sfoglia online o scarica il pdf Manuale d'uso per Frigorifero Electrolux BM Series. Electrolux BM Series 18. Refrigeration
Anche per Electrolux BM Series: Manuale d'uso (18 pagine)
Stampa la pagina
9 care and maintenance electrolux refrigeration
Twist Ice & Serve (where fitted)
Top mount, bottom mount and single door all vertical freezer
models have a twist ice & serve ice cube tray assembly.
To use, remove the tray, fill with water and place back in the
freezer. Once ice has formed (approximately 3 hours) simply
twist the knob at the front clockwise until the ice drops into
the bin below.
A larger bin is provided in some bottom mount models
along with an ice scoop.
Mounting the Twist & serve ice to the other side of the
freezer (top mount and built-in freezer models only)
1. Remove the ice bin and ice cube tray. If the ice tray
assembly is frozen to the carriage, simply squeeze the
tray and shelf together to break the ice.
2. Before you remove the ice carriage, remember to
disengage it from the glass shelf (as shown), as it may
result in damage to the assembly.
3. Remove the centre runner by disengaging it at the front
of the shelf, and removing it from the rear.
4. Refit the runner in to the rear of the shelf on the right
hand side and then engage the front (as shown).
Insert into the slot at
the rear of the shelf
5. Fit the carriage by sliding it into the runners until the front
of the carriage engages with the shelf.
6. Refit the ice tray and ice bin.
Care and maintenance
warning
Before changing any light bulb, switch the power off
at the power point and remove the power cord from
the power point.
Changing the light bulb
• Refrigerator light
1.
Switch off the power at the power
point and remove the refrigerator's
power cord from the power point.
2.
Remove shelves.
3.
Carefully unclip the light cover. You
do this by pulling the upper part of
the cover towards the front of the cabinet.
4.
Unscrew the light bulb and replace it with a bulb
that is the same as the original. If, when you remove
the light bulb the small rubber "O" ring comes out
with the bulb, fit the "O" ring over the new bulb and
screw bulb into the socket (see diagram below).
Never insert your finger into the light bulb
socket to check for the presence of the "O" ring.
5.
Replace the light cover by hooking the light cover
lugs into the bottom of the housing and pressing
the upper part of the cover until it clips in.
6.
Replace shelves.
7.
Wait 5 minutes to ensure pressures in the
refrigeration system are equalized. Then reconnect
and turn the refrigerator on at the power point.
• Freezer light (where fitted)
1.
Switch off the power at the power
point and remove the refrigerator's
power cord from the power point.
2.
Carefully unclip the light cover. You do
this by pulling the light cover tab at the
Then engage
rear towards the front of the cabinet.
into the front
3.
Unscrew the light bulb and replace
of the shelf
it with a bulb that is the same as the
original. If, when you remove the
light bulb the small rubber "O" ring
comes out with the bulb, fit the "O"
ring over the new bulb and screw
bulb into the socket (see diagram
below).
Never insert your finger into the light bulb
socket to check for the presence of the "O" ring.
4.
Replace the light cover by hooking the light cover
lugs into the front of the housing and pressing the
rear of the cover up until it clips in.
5.
Wait 5 minutes to ensure pressures in the
refrigeration system are equalized. Then reconnect
and turn the refrigerator on at the power point.
tips and information
Ensure the 'O' ring is in place before replacing the bulb.
Light bulb
"O" ring
Light socket
Top freezer model
(electronic models only)
Single door all freezer and
built-in freeezer model