Bosch 2 Manuale di istruzioni originale - Pagina 15

Stampa la pagina

1. Starting Operation

OBJ_BUCH-412-001.book Page 34 Thursday, April 3, 2008 3:18 PM

34 | English

Do not exert any force when inserting/re-

moving the battery. Batteries with APT con-

tact (Akku Pack Top) are designed in such a

manner that they can only be inserted into

the power tool or the charger in the correct

position.

To remove the battery 11, squeeze the locking

buttons 12 on both sides and pull the battery

downward out of the handle.

Inserting/Removing the Voltage Adapter

(see figure D)

ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 14CF | 15 | 17 |

22CF | 23 | 29CF | 30

Select the voltage adapter that matches the rat-

ed voltage of your power tool.

The voltage adapters are differentiated, depend-

ing on the voltage, by the colour of the housing of

the D-sub connection plug 26. The housing of the

D-sub connection plug of 9.6 V is light blue, and

that for a voltage of 14,4-V is black in colour.

The adapter housing 28 may be mounted in

or dismounted from the industrial battery-

operated screwdriver only when the con-

stant voltage regulator is switched off or

when the connector 26 is disconnected

from the constant voltage regulator.

Move the rotational direction switch 14 to the

center position. This action locks the on/off trig-

ger switch 13 in the "off" position, which pre-

vents the tool from running.

Insert the adapter housing 28 into the handle of

the power tool. Insure that the adapter housing

is in the correct position and that the locking

buttons 12 engage securely into the handle of

the power tool.

Subsequently, plug the connector 26 of the volt-

age adapter 25 that matches your power tool in-

to the connection socket. Screw the connector

26 tightly in the connection socket 25 by tight-

ening the two screws 27 by hand.

To remove the voltage adapter, loosen the two

screws 27 on the connector 26 of the switched

off constant voltage regulator and and pull the

connector out of the connection socket 25. Sub-

sequently, squeeze the locking buttons 12 on

both sides and pull the adapter housing 28 out

of the hande of the power tool.

3 609 929 B34 | (3.4.08)

ANGLE EXACT 7 – 900 | 10 – 650 | 14 – 420 |

25 – 250 | 30 – 380 | 40 – 280 |

50 – 210

These industrial cordless screwdrivers cannot

be operated with constant voltage regulator.

Changing Application Tools on the Head

with Quick-change Chuck (see figure E)

When working with an application tool, pay

attention that the application tool is firmly

seated on the tool holder. When the applica-

tion tool is not firmly connected with the tool

holder, it can come loose again and not be

controlled.

ANGLE EXACT 2 | 3 | 6 | 7 – 900

A straight screw head with 1/4" quick-change

chuck (Article number 0 607 453 631) is availa-

ble for these industrial cordless angle wrenches.

ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15

An angled screw head with 1/4" quick-change

chuck (Article number 0 607 452 630) is availa-

ble for these industrial cordless angle wrenches.

Inserting

Pull the quick-change chuck 29 to the front. In-

sert the tool 1 into the tool holder 2 and release

the quick-change chuck.

Use only insertion tools with fitting end pieces

(1/4" hexagonal).

Do not attempt to insert quick-change type drill

bits into this chuck.

Industrial cordless angle wrenches with shut-off

clutches are not suitable for drilling applica-

tions. The clutch can shut off automatically and

without warning. When continuing to drill after

the clutch has shut off, the power tool can break

free until the shut-off clutch engages again, and

lead to loss of control.

Removing

Pull the quick-change chuck 29 to the front.

Take the tool 1 out of the tool holder 2 and re-

lease the quick-change chuck.

Bosch Power Tools