Bosch FAP-OC 500Series Manuale di servizio - Pagina 29

Sfoglia online o scarica il pdf Manuale di servizio per Lavatrice Bosch FAP-OC 500Series. Bosch FAP-OC 500Series 41. Built-in wall ovens
Anche per Bosch FAP-OC 500Series: Manuale di istruzioni per l'installazione (21 pagine), Manuale di istruzioni per l'uso (40 pagine), Manuale di installazione (6 pagine), Informazioni sul prodotto (40 pagine), Manuale di installazione (28 pagine), Manuale d'uso (48 pagine), Manuale d'uso (48 pagine), Manuale di installazione (28 pagine), Manuale d'uso e manutenzione (44 pagine), Manuale di installazione (32 pagine), Manuale d'uso e manutenzione / Istruzioni per l'installazione (40 pagine), Manuale di riferimento rapido (4 pagine), Manuale d'uso e manutenzione (27 pagine), Manuale di installazione (24 pagine), Manuale di installazione (32 pagine), Manuale d'uso e manutenzione (24 pagine), Manuale di installazione (28 pagine), Manuale d'uso e manutenzione (21 pagine), Manuale di installazione (32 pagine), Manuale di servizio (36 pagine), Manuale di installazione (32 pagine), Manuale di avvio rapido e di sicurezza (13 pagine)

Stampa la pagina
Bosch FAP-OC 500Series Manuale di servizio
58300000202181 ARA EN B
Error Code Description
Rotary encoder switch short to
E050
Vcc
E101
Cavity 1 / Cavity 2 temperature
E201
sensor open
E104
Cavity 1 / Cavity 2 temperature
E204
sensor shorted
E106
Cavity 1 / Cavity 2 door latch does
E206
not lock
E107
Cavity 1 / Cavity 2 door latch does
E207
not unlock
E115
Cavity 1 / Cavity 2 temperature in
E215
unlocked cavity too high
Copyright by BSH Home Appliances Corporation
This material is intended f or the sole use of BSH authorized persons and may contain conf idential and proprietary inf ormation. Any unauthorized rev iew, use, copy ing, disclosure, or distribution in any f ormat is prohibited.
Novemb er 2018
Cause/Notes
A short to Vcc is detected in an encoder switch
for more than 10 seconds.
Temperature sensor disconnected or has a
faulty connection. Cooling fan will operate at
high speed and heating will stop. After two
consecutive temperature readings are made
successfully, heating will resume and error will
be cleared. See Communication Schematic.
Temperature sensor shorted to ground.
Cooling fan will operate at high speed and
heating will stop. After two consecutive
temperature readings are made successfully,
heating will resume and error will be cleared.
See Communication Schematic
Latch operation not determined by control
module. Door latch does not lock after 1
minute and further attempts will stop. Error
will be cancelled and normal operation
resumed if a locked door is no longer required.
See Cavity 1 (upper) Small Load Schematic
Temperature in cavity is too high or latch
operation not as expected. Door latch does not
unlock after 1 minute and further attempts will
stop. If the latch is detected in open state for
more than 10 seconds, the error will clear and
normal operation will resume. See Cavity 1
(upper) Small Load Schematic
Temperature in unlocked cavity exceeds the
allowable temperature. Oven will stop heating
and door will lock. When temperature reaches
allowable range, door latch unlocks, error is
cleared, and oven will resume heating.
1901 Main St ▪ Suite 600 ▪ Irvine, CA 92614
Service Manual for Bosch 500 Series Built-in Wall Ovens
Suggested Action(s)
 Check all connections and wires to
temperature sensor.
 Check resistance of temperature sensor: if
sensor tests OK, could be control module
problem; if sensor fails, replace sensor.
 Check wires and connections for pinch or
short circuit to ground.
 Check resistance of temperature sensor: if
sensor tests OK, could be control module
problem; if sensor fails, replace sensor.
 Check latch motor and switch
connections/wires.
 Check connections to control board.
 Check wires between control board and
latch. Check operation of door switch.
 Check latch for binding/mechanical latch
failure.
 Check latch motor and switch operation.
 Check door switch operation.
 Check latch for binding/mechanical latch
failure.
 Check for stuck relays.
 Check element operation.
 Check temperature sensor resistance;
replace sensor if necessary.
Page 29 of 41
800 944-2904