Draper Access MultiView Series Istruzioni per l'installazione e il funzionamento - Pagina 3

Sfoglia online o scarica il pdf Istruzioni per l'installazione e il funzionamento per Schermo di proiezione Draper Access MultiView Series. Draper Access MultiView Series 4. 220 volt electric projection screen & masking system

Stampa la pagina

220V Access MultiView by Draper

Adjustments (Screen Motor)

Please Note: Screen limits are factory set for optimum performance of

the screen. A procedure is outlined below for minor tweaks, but any

adjustment of these limits may negatively affect the flatness of the

screen surface and could also void the warranty. Please check with

Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting

limit switches.

"DOWN" LIMIT SWITCH—Down stopping position can be adjusted by turn-

ing the white socket (located on the motor end of screen roller). Turning the

socket counterclockwise will allow the roller to run farther down. Turning it

clockwise will shorten operation, causing it to stop sooner. One full revolution

of the socket will alter the stopping position of the viewing surface by approxi-

mately 32 mm.

"UP" LIMIT SWITCH—Up stopping position can be adjusted by turning the

yellow socket (located on motor end of screen). Turning the socket counter-

clockwise will allow the roller to run farther up. Turning it clockwise will cause

the roller to stop sooner. One full revolution of the socket will alter the stopping

position of the viewing surface by approximately 32 mm.

AT NO TIME SHOULD SURFACE BE UNROLLED ENOUGH TO EXPOSE

ANY PART OF SCREEN ROLLER.

Draper's Tab-Tensioning System is factory-set, and under normal circumstances will not require field adjustment.

If, however, you notice wrinkles, waves or other indications that the tensioning cables need to be adjusted, follow the procedure below.

1 Determine which side requires adjustment.

2 Secure dowel with one hand.

3 Using Phillips-head screwdriver, depress spring-loaded adjustment screw and slowly turn CLOCKWISE TO INCREASE tension,

or COUNTER-CLOCKWISE TO RELEASE tension. The screw adjusts in ¼ turn increments. Adjust only one increment (¼ turn) at a time

4 If problem is not corrected, leave screen in position for 24 hours to allow surface material to stretch into position.

5 If problem still is not corrected, repeat steps 2 and 3.

Caution: Do not touch

or bend surface.

Built-in Low Voltage Control

Junction box at

left end of screen

220V AC supply

Dashed wiring

by electrician

Tab-Tension Adjustment Procedure

TENSIONING

CABLE

ADJUSTMENT

SCREW

DOWEL

Wiring Diagrams for Optional Built-in Controls

Internal screen wiring

White (Neutral)

Black (Hot)

Green (Ground)

VIC220 (220 V AC, white cord & plug)

VIC12 (12 VDC, brown & orange leads)

www.draperinc.com

Adjustments (Masking Motor)

Please Note: Screen limits are factory set for optimum performance of

the screen. A procedure is outlined below for minor tweaks, but any

adjustment of these limits may negatively affect the flatness of the

screen surface and could also void the warranty. Please check with

Draper prior to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in "off" position before adjusting

limit switches.

"DOWN" LIMIT SWITCH—Down stopping position can be adjusted by turning

knob #2 (on motor end of masking roller). Turning the knob counterclockwise

will allow the roller to run farther down. Turning it clockwise will shorten opera-

tion, causing it to stop sooner.

"UP" LIMIT SWITCH—Up stopping position can be adjusted by turning knob

#1 (on the motor end of masking roller). Turning the knob counterclockwise

will allow the roller to run farther up. Turning it clockwise will cause the roller to

stop sooner.

If you encounter any difficulties installing or servicing your Access MultiView

screen, call your dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999 or fax

(765) 987-1689.