Draper Premier Istruzioni per l'installazione
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Schermo di proiezione Draper Premier. Draper Premier 2. 220v premier electric projection screen
Anche per Draper Premier: Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione (2 pagine), Istruzioni Installazione e funzionamento (7 pagine), Istruzioni per l'installazione (4 pagine), Istruzioni per l'installazione (2 pagine), Istruzioni per l'installazione e il funzionamento (4 pagine), Manuale di installazione e istruzioni per l'uso (7 pagine)
Stampa la pagina
Premier Electric Projection Screen by Draper
➀ Read instructions through completely before proceeding.
➁ Follow instructions carefully. Installation con trary to instructions in val i dates warranty.
➂ Screen should be accessible for complete removal should fabric become damaged
or should other ser vice be required.
➃ Screen should be installed level (using a carpenter's level).
➄ Nothing should be fastened to screen dowel or viewing surface.
➅ Operating switch(es) packed separately in screen carton. Do not discard with pack-
ing material.
➆ Screen operates on 110-120V, 60 Hz., 1.1 amp current draw.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
General:
When locating viewing surface and checking clear ance for screen's op er a tion,
remember surface is centered in case. Handle case care ful ly to protect fi nish.
Regardless of mounting method, screen should be positively and securely supported
so that vibration or even abusive pulling on the viewing surface will not cause case to
work loose or fall. Installer must insure that fas ten ers used are of adequate strength and
suitable for the mounting sur face chosen.
Suspended Installation:
Suspend screens from holes in endcaps as shown. "S" hooks, chains (or cable) and
turn buck les should be provided by installer. "S" hooks should go through the rear holes
on the endcap sides (see drawing on page 2), and both ends of the "S" hooks should
be crimped for additional safety. Chains should be attached to beams or other struc tur al
mem bers. Turn buck les should be adjusted so screen hangs level.
Wall Installation:
Mount screen through holes in back of endcaps as shown. Installer should furnish
screws, toggle bolts, molly bolts, nylon or lead anchors as required.
Recessed Installation:
Recess should permit access for removal of screen if necessary. Screen may be
mounted as in suspended or wall installation. Optional Ceiling Opening Trim Kit also
available; see diagram on page 2 and separate instruction sheet (included with Ceiling
Opening Trim Kit).
Elec tri cal Con nec tions
Screen operates on 110-120V, 60 Hz., 1.1 amp current draw. Duty cycle: On 28
seconds/Off 4 minutes. Junction box is located inside left endcap and cover plate is
secured to endcap with two screws. Junc tion box contains terminal strip, per wiring
diagram on reverse.
Screen is shipped with internal wiring complete and control switch(es) fully boxed. Wire
connecting screen to switch(es) and switch(es) to power supply should be furnished by
installer. Connections should be made in ac cor dance with wiring diagram sup plied, and
wiring should comply with na tion al and local elec tri cal codes. Do NOT wire motors in
parallel.
All operating switches should be "Off" before power is connected.
Operation
CAUTION—Important Instructions: Shipping support brackets must be removed
from each end of dowel during initial operation, before screen is operated in UP
direction. After screen is installed, lower viewing surface to access screws holding
brackets to dowel. Loosen hex head screw, remove bracket and retighten screw at each
end of dowel. Raise and lower viewing surface several times to confi rm satisfactory
op er a tion. If viewing surface does not operate properly, turn power off and check
electrical con nec tions.
Screen Case
Back
Ceiling Tile
(By others)
®
Copyright © 2009 Draper Inc.
Form Premier_Inst09-R2 Printed in U.S.A.
Installation Instructions
Caution
Dowel
Please Note: Instructions for adjusting Draper's Tab-Tension System are on page 2.
110-120V Single Station Control—3-position up-off-down switch per mits operation to
be stopped at any point. Factory adjusted limit switches automatically stop screen when
fully down or fully up.
110-120V Multiple Station Control—Switches are similar in ap pear ance to 110-120V
Single Station Control. Screen stops when switch is re leased and may be re start ed in
either direction. Factory adjusted limit switch es stop screen au to mat i cal ly when fully up
or fully down.
24V Control—Three-button up-stop-down switch(es) stop at any point desired, operate
in any sequence. Factory adjusted limit switches au to mat i cal ly stop screen when fully
up or fully down.
Key Operated Switching—Two kinds of key-operated switches are op tion al ly available
with this unit. ➀ The key-operated power sup ply switch controls power to the screen and
switches. When it is "off", the switches will not operate screen. Key may be removed
from the switch in either "on" or "off" position. ➁ A three-po si tion key switch per mits the
screen to be operated directly by key. In this case, the screen's operator must always
have a key.
RS232/Ethernet—Serial communication and network communication optionally
available with wall switches, RF or IR remote.
Limit Adjustments (Standard/Quiet Motors)
Tools needed: Flashlight, small fl athead screwdriver/Allen wrench (4mm or
Screen settings have been factory set as ordered and should not normally require
further adjustment. However, if you fi nd it necessary to adjust for more or less viewing
area, proceed as follows.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing surface
is allowed to run too far up or too far down. When running up, the dowel should
never wrap over the roller. When run to the down limit, a minimum of 1¼ wraps of
fabric must remain on the roller.
The motor limit screws are normally located on the audience left of screen roller, and
the viewing surface rolls off the back of the roller. If the viewing surface is coming off
the front of the roller (motor on left), or the motor is on the audience right of the screen
roller (with viewing surface rolling off the back), reverse the below instructions.
To Reduce Screen Drop
➀ Raise screen surface about 1' above desired setting and turn off.
➁ Turn the DOWN limit screw (I) clockwise (three screw turns = ½ roller revolution).
➂ Test by running screen down and repeat steps 1 and 2 until desired position is
reached.
To Increase Screen Drop
➀ Run screen to the down limit.
➁ With the down switch on, turn the DOWN limit screw (I) counterclockwise (three
turns of screw equals ½ roller revolution) to increase drop.
➂ Test by running screen up about 1' and back down to new down limit.
➃ Repeat steps 2 and 3 until desired position is reached.
CAUTION: At least 1¼ wraps of fabric must remain on the roller when screen is
at the down limit!
Screen is Running Too Far Up
➀ Lower screen surface about 1' below desired setting and turn off.
➁ Turn the UP limit screw (II) clockwise (three screw turns = ½ roller revolution).
➂ Test by running screen up.
➃ Repeat steps 1 through 3 until desired position is reached.
Screen Needs to Run Up More
➀ Run screen down about 1' and turn off.
➁ With the up switch on, turn the UP limit screw (II) counterclockwise (three turns
of screw equals ½ roller revolution).
➂ Repeat steps 1 and 2 until desired position is reached.
CAUTION: Do NOT allow the dowel to wrap up over the roller when the screen
is running up! This could damage the screen.
Shipping
Limit Adjustments (Built-in Low Voltage Motors)
Bracket
➀ Connect the ILT switch to the motor via the terminal blocks, or via the modular port
using four conductor modular cable. When using modular cable, the cable
connectors MUST NOT be crimped in reverse, as with standard telephone cable.
➁ Set the slide switch to the lower position. Press and hold the DOWN button on the
switch to move the viewing surface to the desired lower limit. If the screen moves in
the opposite direction, release the DOWN button and press and hold down the
STOP button for four seconds. This will reverse the operation of the UP and DOWN
switches.
➂ Set the slide switch to the higher position. Move the viewing surface to the desired
upper limit by pressing and holding the UP button on the wall switch.
➃ Return the slide switch to the center position to return to normal operation.
If you encounter any diffi culties installing or ser vic ing your Premier screen, call your
dealer or Draper, Inc. Spiceland, In di ana, U.S.A., (765) 987-7999 or fax (765) 987-7142.
"DOWN" LIMIT ADJUSTMENT
"UP" LIMIT ADJUSTMENT
Continued on Page 2
5
/
").
32