Draper Targa Istruzioni per l'installazione e il funzionamento - Pagina 3

Sfoglia online o scarica il pdf Istruzioni per l'installazione e il funzionamento per Schermo di proiezione Draper Targa. Draper Targa 3. Electrically operated projection screen with motor-in-roller
Anche per Draper Targa: Istruzioni per l'installazione e il funzionamento (4 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione e il funzionamento (4 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione e il funzionamento (4 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Istruzioni per l'installazione e il funzionamento (2 pagine), Manuale di istruzioni (8 pagine)

Stampa la pagina
Draper Targa Istruzioni per l'installazione e il funzionamento
Targa by Draper
Wiring Diagrams Standard and Quiet Motors)
Please Note: Do not wire motors in parallel.
Single Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green/Yellow (Ground)
Dashed wiring
by electrician
Control
Single gang box by others
1
7
switch
Min. 4" x 2
/
" x 1
8
Blue
Red
Black
Location of key
operated on-off
switch if furnished
To 110-120V Line
External Low Voltage and Remote Control
Multiple Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green/Yellow (Ground)
Cap off with wire
nut and tape
Red
Blue
/
" deep
8
Black
Red
Blue
Black
Red
Blue
Single gang box by others
Black
Min. 4" x 2
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110-120V Line
External Two-Way Serial Communication (RS232) with MC1
See separate Serial Communication-RS232 Instruction sheet for enabling RS232 with the MC1.
www.draperinc.com
Wiring Diagrams—Plug & Play 110-120V Motor
with Built-in Low Voltage Controller
Single Low
Voltage Control
Dashed wiring
by electrician
110-120V
Plug
1
/
" x 1
7
/
" deep.
8
8
Wiring Diagrams—110-120V Motor and Quiet Motor
with Built-in Low Voltage Controller
Single Low Voltage Control
Internal Screen Wiring
White (Neutral)
Black
Green/Yellow (Ground)
Dashed wiring
Data Cable
by electrician
Wall Switch,
RF or IR
Receiver,
or integrated
control system
To 110-120V Line
Program LED
Fuse
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver or LED
MC1
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
(765) 987-7999
Multiple Low
Voltage Controls
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data Cable
Wall Switch,
RF or IR
Receiver,
110-120V
or integrated
Plug
control system
Multiple Low Voltage Controls
Dashed wiring
by electrician
To 110-120V Line
White-Common to screen & 110-120V AC Neutral
Red-to Screen (directional)
Brown-to Screen (directional)
Black-Hot to 110-120V AC
Green/Yellow-Ground
Low Voltage Wiring by others
AC Wiring by electrician
Page 3 of 3
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Data
Cables
Wall Switches,
RF or IR
Receivers,
or integrated
control systems
Internal Screen Wiring
White (Neutral)
Black
Green/Yellow (Ground)
Data
Cables
Wall Switches,
RF or IR
Receivers,
or integrated
control systems
Internal Screen Wiring
White (Common)
Red (Up)
Black (Down)
Green/Yellow (Gnd)
To
110-120V
Line
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC