Targa
Section 4 - Limit Adjustments
Figure 6
Please Note: Screen limits are
factory set. Instructions below
for minor adjustments only.
Please check with Draper prior
to resetting screen limits.
CAUTION:
- Be sure all switches are in "off"
position before adjusting limit
switches.
- Be prepared to shut off manually
while testing.
Figure 7
Motor
End
e
n c
d i e
e
A u
S i d
Standard Roll
STANDARD
ROLL
Left hand motor:
White Socket—Down
Yellow Socket—Up
Section 4.2 - ILT Motors with Internal Low-Voltage Control Limit Adjustments
Right hand motor:
White Socket—Up
Please Note: Hold STOP button for 3-5 seconds while in programming mode to reverse motor direction.
Yellow Socket—Down
Figure 8
BACK VIEW OF WALL SWITCH
To Motor
with
Built-In (ILT)
Low Voltage
Slide
Switch
C
o
m
+
m
5V
o
To Motor
DC
n
with
Built-In (ILT)
Low Voltage
POSITION
FUNCTION
DOWN
Set LOWER limit
UP
Set UPPER limit
CENTER
Normal Operation
Please Note: 5V DC must be connected to be
able to set limits using the wall switch.
DOWN Limit
(I)
DOWN Limit (I)
+
Clockwise
I
Clockwise decreases
decreases
down travel.
down travel.
UP Limit (II)
+
I
UP Limit
:
Counterclockwise
(II)
Counterclockwise
increases up travel.
increases up travel.
- Screen may be damaged by
lowering it too far and
exposing roller.
Motor
End
c k
B a
d e
S i
Reverse Roll
REVERSE
ROLL
Left hand motor:
White Socket—Down
Yellow Socket—Up
Right hand motor:
White Socket—Up
Yellow Socket—Down
1. Connect ILT switch to motor via terminal blocks, or via modular
port using a four conductor modular cable. When using modular
cable, cable connectors MUST NOT be crimped in reverse, as
with standard telephone cable.
(For Dry Contacts Wiring Diagram, see p.7.)
2. Set slide switch to lower position. Hold DOWN button to
move viewing surface to desired lower limit. If screen moves
in opposite direction, release DOWN button and hold STOP
button for 4 seconds. This reverses operation of UP and DOWN
switches.
3. Move slide switch into center position. Wait several seconds.
D
Please Note: Do Not move slide switch from DOWN to UP
o
U
w
p
in one motion. This will set limits in same position.
n
4. Set slide switch to higher position. Move viewing surface to
desired upper limit by holding UP button on wall switch.
5. Return slide switch to center position to resume normal
operation.
6. To set viewing surface to alternate format position, move viewing
surface to desired position and press STOP button. Hold STOP
button for at least 3 seconds to record position.
Please Note: This screen is not tested for alternate positions;
surface flatness cannot be guaranteed.
Section 4.1 - Standard Motors/Quiet Motors
:
Section 4.1.1 - "Down" Limit Adjustment
To Reduce Screen Drop:
1. Raise screen surface approximately 1'
and turn switch off.
2. Turn DOWN
limit screw clockwise
(I)
3. Test by lowering screen. Repeat steps 1 and 2 until desired position is reached.
To Increase Screen Drop:
1. Lower screen to down limit.
2. With down switch off, turn DOWN
(3 screw turns = 1/2 roller revolution)
3. Test by raising screen approximately 1'
down limit.
4. Repeat steps 2 and 3 until desired position reached.
Please Note: For Quiet Motor with alternate limit screws:
WHITE screw = UP and RED screw = DOWN.
Section 4.1.2 - "Up" Limit Adjustment
If Screen Raises Too High:
1. Lower screen surface approx. 1'
and turn switch off.
Motor
2. Turn UP
limit screw clockwise
(II)
End
3. Test by advancing screen up.
4. Repeat steps 1 through 3 until desired position is reached.
n c
d i e
If Screen Needs to Raise Higher:
e
A u
S i d
1. Lower screen surface approx. 1'
and turn switch off.
2. With UP switch off, turn UP
(3 screw turns = 1/2 roller revolution)
3. Repeat steps 1 and 2 until desired position is reached.
Waterfall Roll
CAUTION: DO NOT allow dowel to wrap over roller when operating screen!
This could damage screen.
Left hand motor:
White Socket—Up
Yellow Socket—Down
(Fig. 8)
Right hand motor:
White Socket—Down
Yellow Socket—Up
(Fig. 6)
(requires 5/32" (4 mm) hex key)
above desired setting
(30 cm)
(3 screw turns = 1/2 roller revolution)
limit screw counterclockwise
(I)
to increase drop.
then down to new
(30 cm)
below desired setting
(30 cm)
(3 screw turns = 1/2 roller revolution).
e
below desired setting
(30 cm)
limit screw counterclockwise
(II)
.
Please Note: Press and release UP button
on switch to move screen to upper limit.
Press and release DOWN button to move
screen to lower limit.
• While motor is in motion, press STOP
button for less than 2 seconds to stop
viewing surface at present position.
• Once motor is stopped, press STOP
button to move viewing surface to
alternate format position.
• Hold STOP button, when motor is at
rest or in motion, for 3-5 seconds to
record new alternate format position.
• Hold STOP button for 3-5 seconds
while in programming mode to reverse
motor direction.
page 4 of 8
.
Stampa la pagina