Draper 74603 Manuale di istruzioni - Pagina 5

Sfoglia online o scarica il pdf Manuale di istruzioni per Sega Draper 74603. Draper 74603 12. Metal cutting saw 185 mm

WARNING:

Please read the following instructions carefully, failure to do so could lead to serious personal injury. When using electric tools, basic

safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.

Read all these instructions before operating this product and save these instructions.

IMPORTANT:

Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it

was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you.

1. KNOW YOUR POWER TOOL

Read and understand the owner's manual and labels

affixed to the tool. Learn its application and limitations

as well as the specific potential hazards peculiar to

this tool.

2. KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents.

Floors must not be slippery due to oil or sawdust.

3. AVOID DANGEROUS ENVIRONMENTS

Do not use power tools in damp or wet locations, or

expose them to rain. Keep work area well lit. Provide

adequate space surrounding the work area. Do not use

in environments with a potentially explosive atmosphere.

4. KEEP CHILDREN AWAY

All visitors should be kept a safe distance from work area.

5. STORED TOOLS

When not being used, all tools should be stored in a

dry, locked cupboard and out of the reach of children.

6. WEAR PROPER CLOTHING

Do not wear loose clothing, neckties or jewellery (rings,

wristwatches) to catch in moving parts. NONSLIP

footwear is recommended. Wear protective hair covering

to contain long hair. Roll long sleeves above the elbow.

7. USE SAFETY GOGGLES (Head Protection)

Wear CE approved safety goggles at all times. Normal

spectacles only have impact resistant lenses, they are

NOT safety glasses. Also, use face or dust mask if

application is dusty and ear protectors (plugs or muffs)

during extended periods of operation.

8. NOISE LEVELS

Some types of machines may have high noise levels

when working. In such cases ear protection must be worn.

9. VIBRATION LEVELS

Hand held power tools produce different vibration

levels. You should always refer to the specifications and

relevant Health and Safety guide.

10. DUST EXTRACTION

If your tool is fitted with a dust extraction fitting, always

ensure that it is connected and being used with a dust

extractor. Vacuum cleaners can be used if suitable for

the material being extracted.

11. PROTECT YOURSELF FROM ELECTRIC SHOCK

When working with power tools, avoid contact with any

earthed items (e.g. pipes, radiators, hobs and

refrigerators, etc.). If you are using a power tool in

extreme conditions (e.g. high humidity or generating

metal dust), always use an RCD (residual current

device) at the power socket.

12. STAY ALERT

Always watch what you are doing and use common

sense. Do not operate a power tool when you are tired

or under the influence of alcohol or drugs.

13. WHEN WORKING OUT OF DOORS

Only use extension leads designed for that purpose.

14. ACCESS TO MAINS SOCKET

If a stationary machine is fitted with a moulded plug and

cable, the machine should not be positioned so that

access to the mains socket is restricted.

15. DISCONNECT POWER TO THE TOOL

When not in use, before servicing and when changing

accessories such as cutters, etc.

16. AVOID ACCIDENTAL STARTING

Make sure the switch is in the OFF position before

plugging the machine into the power supply.

IMPORTANT NOTE:

Residual Risk. Although the safety instructions and operating manuals for our tools contain extensive instructions on safe working

with power tools, every power tool involves a certain residual risk which can not be completely excluded by safety mechanisms.

Power tools must therefore always be operated with caution!

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS

17. NEVER LEAVE MACHINE RUNNING UNATTENDED

Turn power off. Do not leave machine until it comes to a

complete stop.

18. DO NOT ABUSE THE CORD

Never carry the tool by the power cable or pull it from

the socket. Keep the power cable away from heat, oil

and sharp edges. If the supply cord is damaged, it must

be replaced by the manufacturer or its service agent or

a similarly qualified person in order to avoid hazard.

19. NEVER STAND ON TOOL

Serious injury could occur if the tool is tipped or if the

cutting tool is accidentally contacted. Do not store

materials above or near the tool, so that it is necessary

to stand on the tool to reach them.

20. CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that

is damaged should be carefully checked to determine

that it will operate properly and perform its intended

function. Check for alignment of moving parts, free

running of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation.

A guard or other part that is damaged should be

repaired properly or replaced by an authorized service

centre unless otherwise indicated in this instruction

manual. Have defective switches replaced by an

authorized service facility. Do not use the tool if the

switch does not turn it on and off.

21. KEEP GUARDS IN PLACE

And in working order.

22. MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for the best and safest

performance. Follow instructions for lubricating and

changing accessories. All extension cables must be

checked at regular intervals and replaced if damaged.

Always keep the hand grips on the tool clean, dry and

free of oil and grease.

23. USE RECOMMENDED ACCESSORIES

Consult the owners manual for recommended

accessories. Follow the instructions that accompany

the accessories. The use of improper accessories may

cause hazards .

24. REMOVE ADJUSTING KEYS AND WRENCHES

Form a habit of checking to see that keys and adjusting

wrenches are removed from the tool before turning it on.

25. SECURE WORK

Use clamps or a vice to hold work. This frees both hands

to operate the tool.

26. DO NOT OVERREACH

Keep proper footing and balance at all times.

27. USE RIGHT TOOL

Do not force the tool or attachment to do a job for which

it was not designed.

28. DO NOT FORCE TOOL

It will do the job better and safer at the rate for which it

was designed.

29. DIRECTION OF FEED

Feed work into a blade or cutter against the direction

of rotation of the blade or cutter only.

30. WHEN DRILLING OR SCREWING INTO WALLS

Always make sure there is no danger of hitting any

hidden power cables, water or gas pipes in the wall.

31. HAVE YOUR TOOL REPAIRED BY A QUALIFIED PERSON

This electric tool is in accordance with the relevant safety

requirements. Repairs should only be carried out by

qualified persons using original spare parts, otherwise

this may result in considerable danger to the user.

- 4 -