Alemite 7506-1 Istruzioni per l'installazione e la manutenzione

Sfoglia online o scarica il pdf Istruzioni per l'installazione e la manutenzione per Controllore Alemite 7506-1. Alemite 7506-1 2. 1/4", 3/8", 1/2" filter/regulator

Stampa la pagina

Alemite, LLC

167 Roweland Drive

Johnson City, TN 37601

WARNING

To avoid unpredictable system behavior that can cause personal injury

and property damage:

• Disconnect electrical supply (when necessary) before installation,

servicing, or conversion.

• Disconnect air supply and depressurize all air lines connected to this

product before installation, servicing, or conversion.

• Operate within the manufacturer's specified pressure, temperature,

and other conditions listed in these instructions.

• Medium must be moisture-free if ambient temperature is below

freezing.

• Service according to procedures listed in these instructions.

• Installation, service, and conversion of these products must be

performed by knowledgeable personnel who understand how

pneumatic products are to be applied.

• After installation, servicing, or conversion, air and electrical supplies

(when necessary) should be connected and the product tested for

proper function and leakage. If audible leakage is present, or the

product does not operate properly, do not put into use.

• Warnings and specifications on the product should not be covered by

paint, etc. If masking is not possible, contact your local representative

for replacement labels.

1/4" NPT

Gauge Ports

(2)

1/4" 7504-1, 3/8" 7506-1 Dimensions

2.81

2.74

4.69

5.69

(71)

(70)

(119)

(145)

1/2" 7508 Dimensions

3.24

3.25

4.79

6.97

(82)

(83)

(122)

(177)

Inches (mm)

†

With Auto Float Drain

Distance Required

To Remove All Bowls

Regardless Of

Drain Option

†

5.74

10.38

10.43

2.25

(146)

(264)

(265)

(57)

†

7.00

11.76

11.79

2.75

(178)

(299)

(70)

Installation and Service Instructions

2FR100ALE

1/4" 7504-1, 3/8" 7506-1

1/2" 7508

Filter / Regulator

ISSUED: June, 2014

Supersedes: None

Doc.# 2FR100ALE, EN# 140491, Rev. A

Introduction

Follow these instructions when installing, operating, or servicing the

product.

Specifications

These products are intended for use in general purpose compressed air

systems only.

Maximum Recommended Pressure Drop.................... 10 psig (.7 bar)

Inlet Pressure . ............................................ 0 to 250 psig (0 to 17.2 bar)

Minimum Pressure with Auto Float Drain .................. 15 psig (1.0 bar)

Secondary Pressure . ................................... 2 to 125 psig (0 to 8.6 bar)

Operating Temperature .............................32°F to 175°F (0°C to 80°C)

Flow ....................... 1/4" . ......................................................... 46 SCFM

3/8" . ......................................................... 55 SCFM

1/2" ............................................................. 90 SCFM

Sump Capacity . ..... 1/4" & 3/8" ........................................... 1.75 Ounces

1/2" ........................................................... 2.8 Ounces

Bowl Capacity ....... 1/4" & 3/8" ............................................. 4.4 Ounces

1/2" ........................................................... 7.2 Ounces

Weight . ................... 1/4" & 3/8" .........................................1.6 lb. (0.7 kg)

1/2" ...................................................... 2.5 lb. (1.1 kg)

SCFM = Standard cubic feet per minute at 90 PSIG (6.2 bar inlet) and 10 PSIG

(0.7 bar) pressure drop.

Installation

1. The Filter / Regulator should be installed with reasonable accessibility

for service whenever possible – repair service kits are available. Keep

pipe or tubing lengths to a minimum with inside clean and free of dirt

and chips. Pipe joint compound should be used sparingly and applied

only to the male pipe – never into the female port. Do not use PTFE

tape to seal pipe joints – pieces have a tendency to break off and

lodge inside the unit, possibly causing malfunction. Also, new pipe or

hose should be installed between the Filter / Regulator and equipment

being protected.

2. The upstream pipe work must be clear of accumulated dirt and liquids.

3. Select a Filter / Regulator location as close as possible to the

equipment being protected.

4. Install Filter / Regulator so that air flows in the direction of arrow on

body.

5. Install Filter / Regulator vertically with the bowl drain mechanism at

the bottom. Free moisture will thus drain into the sump ("quiet zone")

at the bottom of the bowl.

6. Gauge ports are located on both sides of the filter/regulator body for

your convenience. It is necessary to install a gauge or socket pipe

plugs into each port during installation.

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE

PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS

CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from The Company, its subsidiaries

and authorized distributors provide product and/or system options for further

investigation by users having technical expertise. It is important that you

analyze all aspects of your application, including consequences of any failure

and review the information concerning the product or systems in the current

product catalog. Due to the variety of operating conditions and applications for

these products or systems, the user, through its own analysis and testing, is

solely responsible for making the final selection of the products and systems

and assuring that all performance, safety and warning requirements of the

application are met.

The products described herein, including without limitation, product features,

specifications, designs, availability and pricing, are subject to change by The

Company and its subsidiaries at any time without notice.