Bosch 46 HBN 44 Manuale di istruzioni per l'installazione - Pagina 5
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Forno Bosch 46 HBN 44. Bosch 46 HBN 44 28. Electric built-in single & double oven
Anche per Bosch 46 HBN 44: Manuale d'uso e manutenzione (48 pagine), Manuale d'uso e manutenzione (48 pagine), Manuale di istruzioni per l'installazione (28 pagine)
Stampa la pagina
INTRODUCTION
Please
read
these
instructions
COMPLETELY
AND CAREFULLY.
They will save you time and
effort and help to ensure
optimum
oven perform-
ance. Be sure to observe
all WARNINGS.
These
installation
instructions
are
intended
for
use by a qualified
installer.
In addition
to these in-
structions
the oven shall be installed:
• In the United
States, in accordance
with the Na-
tional
Electric
Code/State
and Municipal
codes
and/or local codes.
• In Canada,
in accordance
with Canadian
Elec-
tric
Code
C22.1-1atest
edition/Provincial
and
Municipal
codes and/or local codes.
These shall be carefully
followed
at all times.
Note:
If installing
your
oven
in Canada
please
check to make sure that you have a model
with
the UL Canadian
listing
mark,
as
shown below:
The UL Canadian
listing
mark consists
of the cir-
cled UL symbol
preceded
by the letter
"C",
as
shown.
This
should
appear
on the oven's
rating
plate
along
with
the
UL United
States
listing
mark, which
is the circled
UL symbol
above
but
not preceded
by the letter "C".
TOOLS
YOU
WILL
NEED
The following
tools are needed to install your new
oven:
• Tape measure
and straightedge
or ruler
• Pencil
• Phillips
screwdriver
• Level
• Wire cutters and wire stripper
•
1" hole saw
• Hand or saber saw.
POWER
REQUIREMENTS
The oven must be supplied
with the proper
volt-
age and frequency.
The oven is manut:actured
to
be connected
to a three wire or four wire,
single
phase,
240 volt, 60 Hz AC electrical
supply
on a
separate
circuit
fused on both sides of the line. If
a 208 volt circuit
must be used, wiring
inside
the
oven must be modified.
See Connection
to a 208
Volt Circuit,
in this manual.
A circuit breaker
or
time-delay
fuse sized not to exceed
the circuit rat-
ing of the appliance
specified
on the rating plate
located
on the frame behind
the door of the oven
is recommended.
The
oven
must
be supplied
with
copper
wires
ONLY.
It is recommended
that
you
have
the electrical
wiring
and hook-up
of your oven performed
by a
qualified
electrician.
After
installation
is com-
plete
have
the electrician
show
you
where
the
main disconnect
is and which of the circuit break-
ers/fuses
are for the oven.
CHOOSING
OVEN
LOCATION
Carefully
select
the location
where
the oven will
be placed.
The oven should be located
for conven-
ient
use in the
kitchen,
but
away
from
strong
drafts. Strong drafts may be caused by open doors
or windows,
or by heating
and/or air conditioning
vents or fans. Make
sure that electrical
power
can
be provided
to the location
selected.
STEPS
FOR
INSTALLATION
The following
pages
provide
the necessary
infor-
mation
for
proper
installation
of the oven
ar-
ranged
as tk_llows:
• Technical
Data
• Installation
Cutout
Dimensions,
Required
Clearances
and Mounting
instructions
tk_r:
> Undercounter
Installation,
Single Oven
>Wall Installation,
Single Oven
>Wall Installation,
Double
Oven
• Electrical
Supply
and Wiring
Requirements
• Modifications
required
if Connecting
to 208
Volt Circuit.
• Electrical
Connections
for
3-wire
or
4-wire
Branch
Circuit.
• Final Checklist.