Bosch Benchmark Series Manuale di installazione - Pagina 3

Sfoglia online o scarica il pdf Manuale di installazione per Forno Bosch Benchmark Series. Bosch Benchmark Series 32. Built-in wall ovens
Anche per Bosch Benchmark Series: Manuale di servizio (36 pagine), Manuale di riferimento rapido (4 pagine), Manuale di servizio (45 pagine), Manuale di istruzioni per l'installazione (40 pagine), Manuale di avvio rapido e di sicurezza (13 pagine)

Bosch Benchmark Series Manuale di installazione

IMPORTANT SAFETY INSTRUCTIONS

9
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE
F E
S A
T
A N
R T
P O
A D
I M
R E
APPLIANCE AFTER INSTALLATION IS COMPLETE.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE
LOCAL ELECTRICAL INSPECTOR'S USE.
WARNING
If the information in this manual is not followed exactly,
fire or shock may result causing property damage or
personal injury.
WARNING
Do not repair, replace or remove any part of the
appliance unless specifically recommended in the
manuals. Improper installation, service or maintenance
can cause injury or property damage. Refer to this
manual for guidance. All other servicing should be done
by an authorized servicer.

Appliance Handling Safety

Unit is heavy and requires at least two people or proper
equipment to move.
Do not lift appliance by door handle.
Hidden surfaces may have sharp edges. Use caution
when reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with the latest version of one or
more of the following standards:
CAN/CSA C22.2 No. 61 - Household Cooking Ranges
UL 858 - Household Electric Ranges
CAN/CSA C22.2 No. 150 - Microwave Ovens
UL 923 - Microwave Cooking Appliances
UL 507 - Electric Fans
CAN/CSA C22.2 No. 113 - Fans and Ventilators
CSA C22.2 No. 64 - Household Cooking and Liquid-
Heating Appliances
UL 1026 - Electric Household Cooking and Food
Serving Appliances
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
D
A N

Electric Safety

V E
S A
WARNING
Before you plug in an electrical cord or turn on power
supply, make sure all controls are in the OFF position.
For appliances equipped with a cord and plug, do not
cut or remove the ground prong. It must be plugged into
a matching grounding type receptacle to avoid electrical
shock. If there is any doubt as to whether the wall
receptacle is properly grounded, the customer should
have it checked by a qualified electrician.
If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
Installer – show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
Before installing, turn power OFF at the service panel.
Lock service panel to prevent power from being turned
ON accidentally.
Be sure your appliance is properly installed and
grounded by a qualified technician. Installation, electrical
connections and grounding must comply with all
applicable codes.

Microwave Safety

PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE EXPOSURE
TO EXCESSIVE MICROWAVE ENERGY
Do not operate or allow the oven to be operated with
the door open.
Make the following safety checks on all ovens to be
serviced before activating the magnetron or other
microwave source, and make repairs as necessary:
Interlock operation
1.
Proper door closing
2.
Seal and sealing surfaces (arcing, wear, and other
3.
damage)
Damage to or loosening of hinges and latches
4.
Evidence of dropping or abuse
5.
Before turning on microwave power for any service
test or inspection within the microwave generating
compartments, check the magnetron, wave guide or
transmission line, and cavity for proper alignment,
integrity, and connection.
Any damaged or misadjusted components in the
interlock, monitor, door seal, and microwave
generation and transmission systems shall be
repaired, replaced, or adjusted by procedures
described in this manual before the oven is released
to the owner.
A microwave leakage check to verify compliance with
the Federal Performance Standard should be
performed on each oven prior to release to the owner.
E
E S
T H
N S
I O
C T
R U
S T
I N
3